Page Comparison

Velcro )

Step-by-step guide

Step 1

-

– Installing the

Mounting Bracket

c-1024aHeighttruetrue

mounting bracket

1. Position the C-1024A bracket as high as possible, then bolt or Velcro it in place.

Step 2 - Mount Scanner to Bracket

c-1024c,c-1024b,c-1023Heighttruetrue

1. 1. Note, there may be markings on the X-Changer door that act as a guide for where the bracket may be placed.
      

      Image Added

Step 2 – Mounting the scanner to the bracket

1. Attach the C-1024C bracket with the C-1023 scanner to the C-1024B

Plate

1. plate.

Step 3

- Connect the Bracket

– Connecting the bracket assembly

1. Attach the C-1024B assembly to the C-1024A bracket using the 2 set screws

and tilt

1. .

2. Tilt the C-1024B plate completely towards the card dispenser.
   

   Image Added

Step 4

- Align Scanner

– Aligning the barcode scanner

1. Slide the C-1024C bracket

completely to

1. completely to the right, then rotate it clockwise so the silver connector at the top is pointing to about 2 minutes after midnight on the face of a clock (

Use

1. use image below for reference).

2. Screw in the scanner set screw located just to the left of the scanner and tighten slightly.

It is now time to test the adjustment.

1. 
   

Step 5

-

– Final

Adjustments

adjustments

1. Slowly adjust the scanner in millimeter increments by twisting the assembly clockwise while dispensing cards incrementally to test the adjustment.

2. Adjusting the scanner requires some trial and error as the multi-laser design of the scanner means there is no single perfect alignment.

   1. Pressing the “M” or Zebra logo button will allow the scanner to light up, assisting you in positioning the scanner correctly.

3. CCI recommends successfully dispensing 25-50 cards

in a row

1. consecutively with no errors before tightening the set-screw and then testing another 25-50 cards with the door closed and locked.
   

@anonymousINLINE

CCI Technician Information

Reset Barcodes

Reset Barcodes

• DO NOT  perform these next steps unless requested by the CCI technician.
• These bar codes are used exclusively  for the Motorola/Zebra bar code scanners. DO NOT  use on the Symbol type or any other type of scanner. Please consult with CCI if you aren't sure which type of scanner you have.
• Reset the scanner first by unplugging the cable. Plug the cable back in and wait for the beep codes to finish then scan the "Reset Defaults" bar code. The scanner will reset. Scan the "SNAPI" barcode next and the scanner will be setup for your system.

Reset Barcode:

SNAPI Setup barcode:

.Ini settingsFOR TECHNICIAN USE ONLY

[Valuestation1]

BarcodeScanModel=MS4407

ui

rw-tab
title Welch Allyn Scanner

Welch

-Allyn Installation Guide

Step 1 - Install the Scanner

c

Allyn installation guide

Required hardware

Bw part list
Parts C-1010,

c

C-1400-121

HeightfalsefalsetrueThe bar

ImageSize 150 ShowImage true SingleRow true

Step-by-step guide

Step 1 – Installing the scanner

1. The bard code scanner may be attached to the cabinet door with two

strips

1. stips of Velcro or by attaching the

bar code

1. barcode reader to

a scanner plate (

1. the C-1400-121

)

1. scanner plate and then attaching the plate to the cabinet.

   1. It is recommended that there be a 1 ½ to 2-inch space present between the scanner and the card dispenser tray.

Step 2

- Align ScannerOn a Velcro system

– Aligning the scanner

1. When mounted using Velcro, a small card or folded piece of cardboard could be wedged on the top of the barcode unit.

On a

1. When mouted using the scanner plate

system

1. , two 8-32

size

1. philips screws can be inserted into the plate, forcing the scanner to lean

backwards.

1. backward.
   

   Image Added

Hide if
groupIds users specialUsername anonymous matchUsing any
Reset barcodes DO NOT perform these next steps unless conducted by CCI. These barcodes are used exclusively for the Motorola/Zebra barcode scanners. DO NOT use them on the Symbol type or any other type of scanner. Resetting the scanners Unplug the scanner cable. Plug the cable back in and wait for the beeping to stop. Scan the “Reset Defaults” barcode first. The scanner will reset and beep. Scan the “SNAPI” barcode next. The scanner should now be setup for the LaundryCard system. Reset Defaults barcode SNAPI setup barcode INI file settings [Valuestation1] BarcodeScanModel=MS4407

Related documents

Filter by label (Content by label)
showLabels false sort modified showSpace false reverse true cql label = "barcode-scanner" and space = currentSpace ( )