Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID869
KitDescCard Only

  1. Remove existing coin box and coin drop.

  2. Attach the C-5414 Standard Mounting Bracket to the C-6920R1 Mounting Bracket using the C-5420 Screws.

  3. Install the C-6920R1 Mounting Bracket into the coin vault opening. Secure in place using the C-1059 Kep Nuts.

Connect Power

Cci readerinstall kit
KitID794
  1. Tap power as described in the document using theC-5101 Spade Taps provided.
  2. Connect theC-5210 Power Adapter Harnessto the installed spade taps.
  3. Connect theC-5210 Power Adapter Harness to theC-5602 Power Converter.
  4. Connect theC-5500-84 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.
  5. Connect the opposite end of theC-5210 Power Adapter Harnessto theC-5602 Power Converter.
  6. Connect theC-5500-84 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID716
KitDescCoin Drop: Edge Connector
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6357 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID725
KitDescCoin Drop: Set-O-Matic Standard Connection
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6389 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID724
KitDescCoin Drop: Set-O-Matic Terminal Connection
  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the disconnected harness wires to the C-6384Coin Sense Harness, matching color to color.

    1. Machine's Orange wire to Orange and Red wires

    2. Machine's Brown wire to Brown wire

    3. Machine's Blue wire to Blue wire

    4. Machine's Red wire to Red wire

Connect Machine Interface Harness

Cci readerinstall kit
KitID655
KitDescPulse - Edge Connector
  1. Connect the C-5353R1 Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.
Cci readerinstall kit
KitID623
KitDescPulse - Rotary Timer
  1. Connect the C-0119R1F Machine Start Harness to the harness previously connected to the coin drop.
Cci readerinstall kit
KitID666
KitDescPulse - Set-O-Matic
  1. Connect the C-5388 Machine Start Harness to the harness previously connected to the coin drop.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.
  2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-84 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

Cci readerinstall footer