Page Comparison

Cci readerinstall header

Cci readerinstall kit

KitID	584
KitDesc	Coin and Card

Place theC-6700-TEMPDrill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to for further instructions.

Cci readerinstall kit

KitID	906
KitDesc	Card Only - Card Model

Remove the (4) security torx retaining screws on the front of the machine.
Remove the soap tray by pulling it out and pressing on the retaining tab in the rear of the tray.
Locate and remove the (2) security torx screws inside the soap tray opening.
Remove the final (2) torx screws to open the top cover.
Locate a spot on top of the machine to mount the reader.Verify included harnesses will reach desired location without encountering interference from internal machine components. Mark the location using C-6700-TEMP Drill Template.
Refer to for instructions on drilling mounting holes and mounting the reader.

Cci readerinstall kit

KitID	860
KitDesc	Card Only - Coin Model

Remove existing coin box and coin mechanism.
Run reader harnesses through the metercase and out the opening where the coin mechanism was mounted.
Attach the C-5414 Reader Bracketto the C-6911 Metercase Bracketusing(2)C-542010-32 x 1/4 Pan Screws.
Insert the reader harnesses through the hole in the C-6911 Metercase Bracketand then insert the bracket into the metercase opening.
Secure the C-6911 Metercase Bracket to the metercase using the C-0301Mounting Bolt.

Cci readerinstall kit

KitID	663
KitDesc	Tap 120v Power

Locate the incoming power cables in the rear of the machine. This should include a white, black and green wire.
Use the C-5101 Spade Tapsto tap the black (L1) and white (Neutral) wires.
Attach the spade ends of the C-5336 Power Adapter Harnessto the taps. Blue to black, and Brown to White.
Attach the Green ground wire from the C-5336 Power Adapter Harnessto a nearby chassis ground screw.
Connect the 3-pin connector from the C-5336 Power Adapter Harness to the 3-pin connector on the C-5602R1 Power Converter.
Connect the 4-pin connector from the C-5602R1 Power Converter to the 4-pin connector on the C-5500Power Extension Harness.
Mount the C-5602R1Power Converterin the machine by using zip ties to secure it to the machine's wire harness.

Cci readerinstall kit

KitID	721
KitDesc	Coin Drop - Factory Optical

Disconnect the Coin Drop from the Machine Control Assembly.
Connect theC-6362 Coin Sense Harness to the harness connected to the Coin Drop.

Cci readerinstall kit

KitID	1004
KitDesc	Pulse/Serial - Debit (AA3) Connector

Connect theC-5364 Machine Start Harness to theDebit connector on the Machine Control Assembly.
1. If needed, use the C-0126-MLV-EXT15 Extension Harnessto extend the C-5364 Machine Start Harness.

Multiexcerpt include

Feed remaining harness ends through the mounting hole.
Connect the free end of the C-5364 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
(Coin and Card Installations Only) Connect the free end of the C-6362 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
Connect the free end of the C-5500 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

Multiexcerpt include

Multiexcerpt include

Cci readerinstall footer

Versions Compared