Versions Compared

Version Old Version 2 New Version 3
Changes made by

Chris Kite

CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place theC-6700-TEMPDrill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID861
KitDescCard Only - Coin Model w/ High Capacity Metercase

  1. Remove existing coin box and coin drop.

  2. Bridge the Coin Vault Switchconnections using C-5365 Bypass Harness.
  3. Attach C-5760-A Alliance Adapter Bracketto C-6762 Metercase Bracket.
  4. Attach theC-5414 Mounting Bracketto C-6762Metercase Bracket using the(2)C-5420 10-32 x 1/4 Pan Screws.
  5. Mount C-6762 Metercase Bracketinto the front of the metercase, inserting the two studs through the coin slot openings.
    1. Secure to the metercase using (2)C-1059 Kep Nutsand(2)C-1070-WWashers.
Cci readerinstall kit
KitID916
KitDescCard Only - Coin Model w/ Standard Metercase

  1. Remove existing coin box and coin drop.

  2. Attach C-5760-A Alliance Adapter Bracketto C-6760 Metercase Bracket.
  3. Attach theC-5414 Mounting Bracketto C-6760Metercase Bracket using the(2)C-5420 10-32 x 1/4 Pan Screws.
  4. Mount C-6760 Metercase Bracketinto the front of the metercase, inserting the two studs through the coin slot openings.
    1. Secure to the metercase using (2)C-1059 Kep Nutsand(2)C-1070-WWashers.
Cci readerinstall kit
KitID969
KitDescCard Only - Card Model
  1. Place C-5763 TWL Bracketin the intended mounting location. Using the bracket, mark the location of all four mounting holes.
  2. Drill a hole at each marked location using a3/16" drill bit.
  3. Attach C-5414 Mounting Bracketto the front of C-5763 using the(2)C-5420 10-32 x 1/4 Pan Screws.
  4. Mount the C-5763 TLW Bracketusing four using the(2)C-542010-32 x 1/4 Pan Screws.and fasten from the inside of the panel.

Connect Power

Cci readerinstall kit
KitID581
KitDescACA Control - 12VDC Accessory Power
  1. Connect theC-6204-40 12VDC Power Harnessto the H10 Connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 Reader.
Cci readerinstall kit
KitID837
KitDescTitanium Control - 24VAC Transformer
  1. Connect the 2-pin connector from theC-6207 F2, ACA Power Harnessto the 24v transformer behind the front control panel.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
Cci readerinstall kit
KitID663
KitDescTap 120v Machine Power

  1. Tap power as described in the document by connecting theC-5336Power Adapter Harnessto the power distribution panel inside the machine.

    1. 120vac: Connect the blue wire to L1 and the brown wire to N.

    2. 240vac: Connect the blue wire to L1 and the brown wire to L2.

    3. Secure the green wire to the ground screw.

  2. Connect the opposite end of theC-5336Power Adapter Harnessto theC-5602R1Power Converter.

  3. Connect theC-5500Power Extension Harness to the appropriate connector on theC-5602R1Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID700
KitDescCoin Drop - Factory Optical
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect theC-6250 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID704
KitDescCoin Slide - Factory Switch
  1. Disconnect the harness from micro switch.
  2. Connect both ends of C-6253 Coin Sense Harness to the micro switch.

Connect Machine Interface Harness

Cci readerinstall kit
KitID582
KitDescSerial / Pulse - ACA/Titanium Control
  1. Connect theC-5240 Machine Start Harness to the H3connection on the Machine Control Assembly.
Cci readerinstall kit
KitID636
KitDescPulse - Hybrid Coin Slide Control
  1. Connect theC-5256 Machine Start Harness to the manufacturer's harness previously connected to the micro switch used by the coin slide.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole.
  2. (Hybrid Coin Slide Controls Only) Connect the free end of theC-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. (ACA/Titanium Controls Only) Connect the free end of the C-5240 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  4. (Coin and Card Install Only) Connect the free end of the C-6250 or C-6253 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  5. Connect the free end of the C-6207, C-6204-40, or C-5500 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameACA Configuration
PageWithExcerpt_Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameTitanium Configuration (TLW)
PageWithExcerpt_Machine Configuration

Cci readerinstall footer