Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Connect Power

Cci readerinstall kit
KitID595

  1. Tap power as described in the document by connecting the C-5210 Power Adapter Harness to the power distribution panel inside the machine.

    1. 120vac: Connect the blue wire to L1 and the brown wire to N.

    2. 240vac: Connect the brown and blue wires to L1 and L2 wires.

    3. Connect the green wire to the ground wire.

  2. Connect the opposite end of the C-5210 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID725
KitDescCoin Drop: Set-O-Matic
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6389 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID890
KitDescCoin Drop: Keltner SR1-WIR
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the 6-pin male connector from the C-6380 Coin Sense Harness to the 6-pin female connector on the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID666
KitDescPulse - Set-O-Matic
  1. Connect the C-5388 Machine Start Harness to the coin connector on the Machine Control Assembly.
Cci readerinstall kit
KitID890
KitDescPulse - Keltner SR1-WIR
  1. Connect the 6-pin female connector from the C-6380 Machine Start Harness to the 6-pin male coin connector on the Machine Control Assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in the Touchscreen Reader Mounting Guide (F2 & F3).
  2. Connect the free end of the pulse start harnesses (white connector), connect to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of theCoin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the Touchscreen Reader Mounting Guide (F2 & F3).

Machine Configuration

TODO

Cci readerinstall footer