Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID867
KitDescCard Only - Coin Prepped Models
  1. Secure the mounting bracket from the C-5414 F2 Mounting Bracket to the C-6601Spacer Plate using the C-5702Chase Nipple and the C-5703 Nut.
  2. Feed the remaining harness ends through the open face of theCoin Vault.
  3. Spread the C-6602 Vault Mount Bracketwings outward before insertion to lock bracket into place.
  4. Feed remaining harness ends through the C-6602Vault Mount Bracket.
  5. Insert the C-6602Vault Mount Bracketinto theCoin Vault.
  6. Feed the remaining harness ends through the combined C-5414F2 Mounting Bracketand C-6601Filler Plate.
  7. Secure thecombined C-5414 F2 Mounting Bracket and C-6601 Filler Plate to the C-6602 Vault Mount Bracket with the C-0144 Screws.
  8. Install the C-0963Drop Cover over the cavity left by theCoin Drop and secure with C-1062 Kep Nuts.

Connect Power

Cci readerinstall kit
KitID473

  1. Tap power as described in the document by connecting the C-5338 Power Adapter Harness to the power distribution panel inside the machine.

    1. 120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-5338 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID704
KitDescCoin Drop: Factory - Micro Switch
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID707
KitDescCoin Drop: Factory - Optical Sensor
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6258 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID709
KitDescCoin Drop: Factory - Imonex
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6261 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID723
KitDescCoin Drop: Aftermarket - Imonex
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6382 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID634
KitDescPulse
  1. Connect the C-5254 Machine Start Harness to the P2 connector on the Machine Control Assembly.
Cci readerinstall kit
KitID578
KitDescSerial
  1. Connect the C-0127-MLV Machine Start Harness to the P23 connector on the Machine Control Assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in theFasCard Mounting Guide.
  2. Connect the free end of the Machine Start Harness.
    1. If following steps for a serial Machine Start Harnessto port 5 (Serial Connection Port) as shown in the image above.
    2. If following steps for a pulse Machine Start Harnessto port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the Coin Sense Harnessto port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

Cci readerinstall footer