Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID598
KitDescCard Only - Coin Model

  1. Remove existing coin box and coin mechanism.

  2. Run reader harnesses through the metercase and out the opening where the coin mechanism was mounted.

  3. Attach the C-5414 Reader Bracketto the C-6911 Metercase Bracketusing (2)C-542010-32 x 1/4 Pan Screws.
  4. Insert the reader harnesses through the hole in the C-6911 Metercase Bracketand then insert the bracket into the metercase opening.
  5. Secure the C-6911 Metercase Bracket to the metercase using the C-0301Mounting Bolt.

Connect Power

Cci readerinstall kit
KitID595
KitDescTap Machine Power
  1. Use the C-5101 Spade Tapson the incoming power.
    1. Tap theL1wire.
    2. Tap theNwire.
    3. Tap theGround wire.
  2. Take the C-5210 Power Adapter Harnessand connect the red tab connectors to the following wires:
    1. Connect thebluewire to theL1wire.
    2. Connect thebrownwire to theNwire.
    3. Connect the green/yellow wire to theGroundwire.
  3. Connect the 3-pin connector from the C-5210 Power Adapter Harnessto the matching connection on the C-5602R1Power Converter.
  4. Connect the4-pinconnector from the C-5602R1 Power Converterto the matching connection on the C-5500Power Extension Harness.

Connect Coin Sense Harness

Cci readerinstall kit
KitID721
KitDescCoin Drop: Factory
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6362 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID1004
KitDescPulse - Debit/AA3 Connection
  1. Connect the C-5364 Machine Start Harness to the Debit/AA3 connector on the Machine Control Assembly.
    1. If needed, use the C-126-MLV-EXT15 Extension Harness to extended the reach of the harness.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5364 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. (Coin and Card Installations Only) Connect the free end of the C-6362 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameMayTag Gen1 MLV+ Pulse
PageWithExcerpt_Machine Configuration

Cci readerinstall footer