Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID872
KitDescCard Only
  1. Install theC-0961 Jam Ring into the coin vault. TheJam Ringshould be installed into the coin vault so that it is within 1.5" of front panel of the machine to allow the mounting bracket to be attached.
  2. To install theJam Ringinsert the ring so the small portion is on the bottom. Insert at an angle, so the top of theJam Ringis inserted first. Once the ring is in position, pull the top of theJam Ringtowards the front of the machine until it locks into place.
  3. Using theC-5751Screws, attach theC-6960Mounting Bracketto theC-0961Jam Ring.
  4. Attach the C-5414 Standard Mounting Bracket to the C-6960 Mounting Bracket using the C-5420 Screws.

Connect Power

Cci readerinstall kit
KitID595

  1. Tap power as described in the document by connecting the C-5210 Power Adapter Harness to the power distribution panel inside the machine.

    1. 120vac: Connect the blue wire to L1 and the brown wire to N.

    2. 240vac: Connect the blue wire to L1 and the brown wire to L2.

    3. Connect the green wire to the ground wire..

  2. Connect the opposite end of the C-5210 Power Adapter Harness to the C-5602R1 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID704
KitDescCoin Drop: Factory
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6253 Coin Sense Harness to the Microswitch on the coin drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID636
KitDescPulse
  1. Connect the C-5256 Machine Start Harness to the Coin Drop Coin Harness connected to the machine control assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in the Touchscreen Reader Mounting Guide (F2 & F3).
  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6253 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the Touchscreen Reader Mounting Guide (F2 & F3).

Machine Configuration

TODO

Cci readerinstall footer