Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID841
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID906
KitDescCard Only - Coin Ready

  1. Remove existing coin box.

  2. Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

  3. Bend the side tabs of theC-0941Vault Coveroutward and install into the coin vault. The tabs should snap into place securing the bracket.

  4. Place theC-6700-TEMPDrill Template on the desired mounting location.

  5. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  6. Refer to for further instructions.

Cci readerinstall kit
KitID912
KitDescCard Only - Card Ready

  1. Place theC-6700-TEMPDrill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Connect Power

Cci readerinstall kit
KitID581

  1. Connect theC-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly.

    1. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of theC-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID700
KitDescCoin Drop: Factory
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID582
KitDescSerial or Pulse
  1. Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.

Optional: Stack Add-on Installation

Cci readerinstall kit
KitID938
KitDescPulse and Serial
  1. Run C-5240 Machine Start Harness and C-6250 Coin Sense Harness to the second Machine Control Assembly.
  2. Connect C-5240 Machine Start Harness to the H3 connection and the C-6250 Coin Sense Harness to the Coin 1 connection on the second Machine Control Assembly.
  3. Connect the C-6401 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
    1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Unit 1 on the Stack Add-on Board.
    2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Unit 2 on the Stack Add-on Board.
  4. Connect the Coin Sense Harness connected to the upper pocket Coin Drop to port 3 (Coin 1 Sense Harness Connection Port) on the F2 reader.
  5. Connect the Coin Sense Harness connected to the lower pocket Coin Drop to port 4 (Coin 2 Sense Harness Connection Port) on the F2 reader.


Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5240 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-6204-40 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

ACA machines using a serial configuration require dip switch 3 on theMachine Control Boardto be set to the 'ON' position.Leave all other dip switches as is.

Cci readerinstall footer