Page Comparison

1. Place the C-6700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to for further instructions.

1. Remove Coin Box.
2. Disconnect harness connection from the Vault Switch. Connect both ends to the C-5365 Bypass Harness.
3. Spread the C-6936 Vault Mount Bracket wings to lock it into place once installed.
4. Insert the C-6936 Vault Mount Bracket into the Coin Vault.
5. Use the C-0144 screws, attach the C-5414 F2 Mounting Bracketto the C-6936Vault Mount Bracket.

1. Install the C-6970R1Alliance Mounting Bracket into the opening on the control panel for mounting card readers and coin drops.
2. Attach the C-5414 F2 Mounting Bracket to the C-6970Alliance Mounting Bracketand secure using the C-1060Screws.

1. Tap power as described in the document using the C-5101 Spade Taps provided.
2. Connect the opposite end of the C-5210 Power Adapter Harness to the C-5602 Power Converter.
3. Connect the C-5500-115 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

1. Disconnect the Coin Drop from the Machine Control Assembly.
2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

1. Connect the C-5300-NC Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.

1. Connect the C-0110-TOP Machine Start Harness to the H3 connector on the Machine Control Assembly.

1. Run C-0110-TOP-144 Machine Start Harness to the second Machine Control Assembly.
2. Connect C-0110-TOP-144 Machine Start Harness to the H3 connection on the second Machine Control Assembly.
3. Connect the C-6401 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
   1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Unit 1 on the Stack Add-on Board.
   2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Unit 2 on the Stack Add-on Board.

The following steps assume the start and coin sense harnesses are already connected to the upper pocket control.

1. Locate area to mountC-6411Serial Stack Add-On Board.
   1. Must be close enough to reader mounting location to connect the harness to.
   2. Must be on a surface that does not received direct exposure from any heating elements (If applicable.)
2. Clean mounting location to remove any dust and residue if needed.
3. Remove the sticker from the back of the C-6411Serial Stack Add-On Boardto expose the adhesive and apply to the mounting location.
4. Connect the white, 7-pin connector from theC-0110-TOP to the H3connection on the lower pocket's Machine Control Assembly.
5. Connect the the clear, 3-pin circuit board end from theC-6250-144 Coin Sense Harnessto the lower pocket's Coin Drop.

The following steps assume the start and coin sense harnesses are already connected to the upper pocket control.

1. Locate area to mountC-6411Serial Stack Add-On Board.
   1. Must be close enough to reader mounting location to connect the harness to.
   2. Must be on a surface that does not received direct exposure from any heating elements (If applicable.)
2. Clean mounting location to remove any dust and residue if needed.
3. Remove the sticker from the back of the C-6411Serial Stack Add-On Boardto expose the adhesive and apply to the mounting location.
4. Connect the white, 7-pin connector from theC-0110-TOP to the H3connection on the lower pocket's Machine Control Assembly.
5. Apply the C-5033 Label over the coin drop opening for the lower pocket.