Versions Compared

Old Version 4

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 5

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID857
KitDescCard Only - 10° Panel Coin Models

  1. Remove existing coin box and coin drop.

  2. Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
  3. Attach theC-5414 F2 Mounting Bracketto the C-6765-W-R1 Metercase Bracketusing C-5702 Chase Nippleand C-5703 Lock Nut.
  4. Run any card reader harnesses through the coin slot openings and the circular hole in theC-6765-W-R1Metercase Bracket.

  5. Install the C-6765-W-R1Metercase Bracketso that the two threaded posts insert into the coin drop slots. Then secure it to the machine using theC-1059 Kep Nutsand C-1070-WWashers.

Cci readerinstall kit
KitID906
KitDescCard Only - All Card Models

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Connect Power

Cci readerinstall kit
KitID581
KitDescACA Controls
  1. Connect the C-6204-40 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.
  2. Connect the green wire to a chassis ground.
  3. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
Cci readerinstall kit
KitID837
KitDescTitanium Controls
  1. Connect the 2-pin connector from theC-6207 F2, ACA Power Harnessto the 24v transformer behind the front control panel.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
Cci readerinstall kit
KitID595
KitDescHybrid Coin Slides
  1. Tap power as described in the document using theC-5101 Spade Taps provided.
  2. Connect theC-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to theC-5602 Power Converter.
  3. Connect theC-5500 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID700
KitDescFactory Standard Coin Drop
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect theC-6250 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID704
KitDescFactory Standard Coin Slide
  1. Locate the micro switch on the coin slide assembly for the upper pocket.
  2. Disconnect the harness connected to the microswitch and connect C-6253 Coin Sense Harness to the spade tabs on the micro switch.

Connect Machine Interface Harness

Cci readerinstall kit
KitID645
KitDescPulse - Coin Connection
  1. Connect theC-5300-NC Machine Start Harness to theCoin 1 connector on the Machine Control Assembly.
Cci readerinstall kit
KitID582
KitDescSerial Communication / Serial Pulse
  1. Connect theC-5240 Machine Start Harness to the the H3connection on the Machine Control Assembly or Communication board.
Cci readerinstall kit
KitID636
KitDescHybrid Coin Slide Switch
  1. Connect theC-5256 Machine Start Harness to the the harness previously connected to the coin slide microswitch spade tabs.

Connect Stack Add-On Components

Cci readerinstall kit
KitID1023
KitDescSerial Stack Add-On - Card Only - Card Models
  1. Connect theC-5240 Machine Start Harness to the the H3connection on the Machine Control Assembly or Communication board on the lower pocket control.
Cci readerinstall kit
KitID938
KitDescSerial Stack Add-On - Coin and Card Install
  1. Connect theC-5240 Machine Start Harness to the the H3connection on the Machine Control Assembly or Communication board on the lower pocket control.
  2. Disconnect the Coin Drop from the Machine Control Assembly lower pocket control.
  3. Connect theC-6250 Coin Sense Harness to the harness connected to the lower pocket's Coin Drop.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole.
  2. If using the C-5300-NC or C-5256 Machine Start Harness, connect the free end to port 2 (Pulse Connection Port) as shown in the image above.
  3. If using the C-5240 Machine Start Harness, connect the free end to port 5 (Serial Connection Port) as shown in the image above.
    1. If installing a Stack Add-On kit, install the C-6401 MLV Add-On Boardinto port 5 (Serial Connection Port). Connect the C-5240 Machine Start Harness from the top pocket's control to Unit 1 on the C-6401 MLV Add-On Board. Connect the C-5240 Machine Start Harness from the bottom pocket's control to Unit 2 on the C-6401 MLV Add-On Board.
  4. For Coin and Card setups, connect the free end of the C-6250 or C-6253 Coin Sense Harnessto port 3 (Coin Sense Harness Connection Port) as shown in the image above.
    1. If installing a Stack Add-On kit with a coin and card setup, connect the C-6250 Coin Sense Harness from the lower pocket's coin drop to Port 4 (Coin Sense 2 Harness Connection Port) as shown in the image above.
  5. Connect the free end of the C-6204-40, C-6207, or C-5500 Power Harness to port 1 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameACA Configuration
PageWithExcerpt_Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameTitanium Configuration (Small Dryer)
PageWithExcerpt_Machine Configuration

Cci readerinstall footer