Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID841
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID842
KitDescCard Only

  1. Remove existing coin box and coin drop.

  2. Install C-0905 Drop Cover where the coin drop was previously mounted. Secure in place using the existing hardware.
  3. Align the C-5414 Mounting Bracket with the C-6936 Vault Bracket with the C-5414 Mounting Bracket on top. Run all reader harnesses through the holes in the brackets.

  4. Bend the side tabs of the C-6936 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  5. Attach C-5414 Mounting Bracket to the C-6936 Vault Bracket using C-0144 Screws.

Connect Power

Cci readerinstall kit
KitID805
  1. Tap power as described in the document by connecting the C-5211 Power Adapter Harness to the male spade connectors on the machine power panel.
    1. Connect the green wire to the ground terminal.
    2. A corner of the power panel cover may need to be bent slightly to allow the power harness egress.
  2. Connect the opposite end of the C-5211 Power Adapter Harness to the C-5602 Power Converter.
  3. Connect the C-5500-60 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID704
KitDescCoin Drop: Factory
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID636
KitDescPulse
  1. Connect the C-5256 Machine Start Harness to the harness previously connected to the micro switch.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in the F2: FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6253 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-60 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

Cci readerinstall footer