Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID940
KitDescCard Only - Coin Model

  1. Remove existing coin box and coin drop.

  2. Install the C-0913 Drop Cover in the coin drop opening and secure using the C-1062 Keps Nuts.
  3. Run all reader harnesses through coin vault and then the hole of theC-6936Vault Bracket.

  4. Bend the side tabs of theC-6936Vault Bracketoutward and install into the coin vault. The tabs should snap into place securing the bracket.

  5. Run all reader harnesses through the central hole of theC-5414Reader Bracket.

  6. Attach theC-5414Reader Bracketto theC-6936Vault Bracketusing theC-0144screw so that it is flush with the front panel.

Cci readerinstall kit
KitID995
KitDescCard Only - Card Model

  1. Remove factory card reader interface bracket.

  2. Attach C-5414 Reader Bracket to the C-6918 Mounting Bracket using (2) C-5420 10-32 x 1/4" Pan Screw.
  3. Install the C-6918 Mounting Bracket in the payment device opening and secure using the (2) C-1062 Keps Nuts.
  4. Run all reader harnesses through the center hole in the C-6918 Mounting Bracket.

Connect Power

Cci readerinstall kit
KitID595
KitDescTap Machine Power
  1. Use the C-5101 Spade Tapson the incoming power.
    1. Tap theL1wire.
    2. Tap theN / L2wire.
    3. Tap theGround wire.
  2. Take the C-5210 Power Adapter Harnessand connect the red tab connectors to the following wires:
    1. Connect thebluewire to theL1wire.
    2. Connect thebrownwire to theN / L2wire.
    3. Connect the green/yellow wire to theGroundwire.
  3. Connect the 3-pin connector from the C-5210 Power Adapter Harnessto the matching connection on the C-5602R1Power Converter.
  4. Connect the4-pinconnector from the C-5602R1 Power Converterto the matching connection on the C-5500Power Extension Harness.

Connect Coin Sense Harness

Cci readerinstall kit
KitID721
KitDescFactory Coin Drop
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6362 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID997
KitDescPulse - AA3/Debit Connection
  1. Connect the C-5370 Machine Start Harness to the 8-pin J6 harness connection accessible near the coin drop.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5370 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6362 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

  1. Enter Service Mode and navigate toJ option.
  2. Set option to J.d.
  3. Exit Service Mode.
Cci readerinstall footer