Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place theC-6700-TEMPDrill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID906
KitDescCard Only - Card Models

  1. Place theC-6700-TEMPDrill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID861
KitDescCard Only - Reader Control Coin Models
  1. Remove thecoin drop and coin box.
  2. Remove Vault Switchand bridge the wires previously connected to the Vault Switchwith the C-5365 Bypass Harness.
  3. Secure C-5414 F2 Mounting Bracketto the C-6903Mounting Bracket using the(2)C-542010-32 x 1/4 Pan Screws.
  4. Attach the C-5760-AAdapter Bracketto the C-6762 Mounting Bracketto the captured nut on the inside of the C-6762 Mounting Bracket.
  5. Run all reader harnesses through the metercase and out the opening where the coin drop normally mounts.
  6. Run all reader harnesses through the circular opening on theC-6762Mounting Bracket.
  7. Install theC-6762Mounting Bracketinto the front opening of the metercase so the two threaded posts of the C-5760-A Adapter Bracketline up with the openings for the coin slots. Secure in place using theC-1059 Nutand C-1070-W Washer.
Cci readerinstall kit
KitID857
KitDescCard Only - White 10° Panel Coin Models

  1. Remove existing coin box and coin drop.

  2. Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
  3. Attach theC-5414 F2 Mounting Bracketto the C-6765-W-R1 Metercase Bracketusing (2) C-5420 10-32 x 1/4 Pan Screws.
  4. Run any card reader harnesses through the coin slot openings and the circular hole in theC-6765-W-R1Metercase Bracket.

  5. Install the C-6765-W-R1Metercase Bracketso that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nutsand (2) C-1070-WWashers.

Cci readerinstall kit
KitID996
KitDescCard Only - Black 10° Panel Coin Models

  1. Remove existing coin box and coin drop.

  2. Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
  3. Attach theC-5414 F2 Mounting Bracketto the C-6765-B Metercase Bracketusing (2) C-5420 10-32 x 1/4 Pan Screws.
  4. Run any card reader harnesses through the coin slot openings and the circular hole in theC-6765-BMetercase Bracket.

  5. Install the C-6765-BMetercase Bracketso that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nutsand (2) C-1070-WWashers.

Connect Power

Cci readerinstall kit
KitID581
KitDescACA Controls - 12VDC Accessory Power

  1. Connect theC-6204-40 12VDC Power Harness to theH10connection on themachine control assembly.

    1. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of theC-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.

Cci readerinstall kit
KitID837
KitDescTitanium Controls - 24VAC Transformer
  1. Connect the 2-pin connector from theC-6207 F2, ACA Power Harnessto the 24v transformer behind the front control panel.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID700
KitDescCoin Drop - Factory Optical
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the Coin 1 machine harness connected to the coin drop.
Cci readerinstall kit
KitID928
KitDescCoin Drop - Factory Dual Optical
  1. Disconnect both of the Coin Drops from the Machine Control Assembly.
  2. Connect one of the C-6250 Coin Sense Harness to the Coin 1 machine harness and the other to the Coin 2 machine harness.

Connect Machine Interface Harness

Cci readerinstall kit
KitID582
KitDescSerial Communication / Serial Pulse
  1. Connect theC-5240Machine Start Harness to the H3connector on the Machine Control Assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5240 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. (Coin and Card Installations Only) Connect the free end of theCoin 1C-6250 Coin Sense Harnessto port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. (Coin and Card Installations with Factory Dual Optical kits Only) Connect the free end of the Coin 2 C-6250 Coin Sense Harnessto port 4 (Coin Sense Harness Connection Port) as shown in the image above.
  5. Connect the free end of the C-6207 or C-6204-40 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameACA Configuration
PageWithExcerpt_Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameTitanium Configuration (FLW)
PageWithExcerpt_Machine Configuration

Cci readerinstall footer