Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

-

Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID959
KitDescCard Only

  1. Remove existing payment device and coin box.

  2. Install the C-6925A Coin Vault Bracketin the coin vault. Line up the C-6925B Coin Vault Cover Bracketover the coin vault so the outer set of holes line up with the threaded holes on the C-6925A Coin Vault Bracket and attach with the C-57518-32 x 2-1/2" Phillips Screws.

  3. Use the (2) C-5420 10-32 x 1/4" Phillips Screwsto attach the C-5414 Reader Bracketto the C-6925BCoin Vault Cover Bracket.

  4. Install the C-0913 Drop Cover into the coin drop opening. Secure in place using the (4) C-1062 4-40 Keps Nuts.
  5. Apply C-5035 Labelonto the C-0913 Drop Cover.
  6. After connecting all harnesses to the reader, use the (2) C-5416 8-32 x 3/8" Torx Screws to attach the reader to the C-5414Reader Bracket.

Connect Power

Cci readerinstall kit
KitID802

  1. Tap power as described in the document by connecting the C-5210 Power Adapter Harness to the power distribution panel inside the machine.

    1. 120vac: Connect the blue wire to L1 and the brown wire to N.

    2. 240vac: Connect the blue wire to L1 and the brown wire to L2.

    3. Secure the green wire to the ground wire.

  2. Connect the opposite end of the C-5210 Power Adapter Harness to the C-5602R1 Power Converter.

  3. Connect the C-5500-60 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID722
KitDescCoin Drop: Factory
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6368 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID664
KitDescPulse
  1. Connect the C-5369R1 Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in the Touchscreen Reader Mounting Guide (F2 & F3).
  2. Connect the free end of the C-5369R1 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-6368 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-60 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the Touchscreen Reader Mounting Guide (F2 & F3).

Machine Configuration

TODO

Cci readerinstall footer