Versions Compared

Version Old Version 2 New Version 3
Changes made by

Chris Kite

CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID863
KitDescCard Only

Coin Ready

  1. Remove existing coin box.

  2. Bend the side tabs of the C-6602 Vault Mount Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  3. Use the C-0144 Screws, attach the C-5414 F2 Mounting Bracket to the C-6602Vault Mount Bracket

Cci readerinstall kit
KitID865
KitDescCard Ready
  1. Install the C-6970 Bracket on the control panel.
  2. Attach the C-5414 F2 Mounting Bracket onto the C-6970 Bracket using the C-1060 screws.

Connect Power

Cci readerinstall kit
KitID581

  1. Connect the C-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly.

    1. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID700
KitDescCoin Drop: Factory
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID928
KitDescCoin Drop: Factory - Dual Coin
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect aC-6250 Coin Sense Harness to the harness connected to the Coin 1 Drop.
  3. Connect aC-6250 Coin Sense Harness to the harness connected to the Coin 2 Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID645
KitDescPulse
  1. Connect the C-5300-NC Machine Start Harness to the Machine Control Assembly.
Cci readerinstall kit
KitID582
KitDescSerial
  1. Connect the C-5240 Machine Start Harness to the Machine Control Assembly.

For Card only

  1. Connect the C-5365 Bypass Harness to the appropriate connections to bypass the coin vault switch. **Needs Better Verbiage)

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in theFasCard Mounting Guide.
  2. Connect the free end of the Machine Start Harness.
    1. If following steps for a serial Machine Start Harnessto port 1 (Serial Connection Port) as shown in the image above.
    2. If following steps for a pulse Machine Start Harnessto port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of theC-6250Coin Sense Harnessto port 3 (Coin 1 Sense Harness Connection Port) as shown in the image above.
    1. If using a dual coin drop, connect the second C-6250 Coin Sense Harnessto port 4 (Coin 2 Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the Power Extension Harness to port 4 (C-5500 Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

ACA machines using a serial configuration require dip switch 3 on theMachine Control Boardto be set to the 'ON' position.Leave all other dip switches as is.

Cci readerinstall footer