Versions Compared

Old Version 9

changes.mady.by.user Adam Arafat

Saved on

compared with

New Version 10

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID591
KitDescCoin and Card

  1. Place theC-5700-TEMPDrill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID813
KitDescCard Only - Coin Model

  1. Remove the mounting bolt securing the coin drop to the metercase. Then remove the coin drop and coin box.

  2. Run reader harnesses through the metercase and the hole on the C-5771 Metercase Bracket.

  3. Install C-5771Metercase Bracketinto the metercase and secure using C-0303 Mounting Bolt.
Cci readerinstall kit
KitID904
KitDescCard Only - Card Model

  1. Remove the (4) security torx retaining screws on the front of the machine.

  2. Remove the soap tray by pulling it out and pressing on the retaining tab in the rear of the tray.

  3. Locate and remove the (2) security torx screws inside the soap tray opening.
  4. Remove the final (2) torx screws to open the top cover.
  5. Locate a spot on top of the machine to mount the reader.Verify included harnesses will reach desired location without encountering interference from internal machine components. Mark the location using C-5700-TEMP Drill Template.
  6. Refer to for instructions on drilling mounting holes and mounting the reader.

Connect Power

Cci readerinstall kit
KitID663
KitDescTap Machine Power

  1. Locate the incoming power cables in the rear of the machine. This should include a white, black and green wire.

  2. Use the C-5101 Spade Tapsto tap the black (L1) and white (Neutral) wires.
  3. Attach the spade ends of the C-5336 Power Adapter Harnessto the taps. Blue to black, and Brown to White.
  4. Attach the Green ground wire from the C-5336 Power Adapter Harnessto a nearby chassis ground screw.
  5. Connect the 3-pin connector from the C-5336 Power Adapter Harness to the 3-pin connector on the C-5602R1 Power Converter.
  6. Connect the 4-pin connector from the C-5602R1 Power Converter to the 4-pin connector on the C-5500Power Extension Harness.
  7. Mount the C-5602R1Power Converterin the machine by using zip ties to secure it to the machine's wire harness.

Connect Coin Sense Harness

Cci readerinstall kit
KitID693
KitDescFactory - Optical Coin Drop
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect theC-5362 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID1004
KitDescPulse - AA3 / Debit Connection
  1. Connect theC-5364 Machine Start Harness to theAA3 connector on the Machine Control Assembly.
    1. If needed, use the C-0126-MLV-EXT15 Extension Harnessto extend the C-5364 Machine Start Harness.

Connect and Mount Reader

Image Added

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5364 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of theC-5362 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

  1. Enter Service Mode and navigate toJ option.
  2. Set option to J.d.
  3. Exit Service Mode.
Cci readerinstall footer