Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID841
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify that included harnesses will reach the desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID959
KitDescCard Only

  1. Remove existing coin drop.

  2. Install C-0913 Drop Cover where the coin drop was previously mounted. Secure using (4) C-1062 4-40 Keps Nuts.

  3. Place theC-6700-TEMPDrill Template on the desired mounting location.

  4. Verify that included harnesses will reach the desired location without encountering interference from internal machine components.

  5. Refer to for further instructions.

  6. Optional: Use C-5710 Rubber Grommet to protect harnesses from damage during machine operation if any secondary hole is cut internally to run harnesses to the reader mounting location.

Connect Power

Cci readerinstall kit
KitID804
  1. Tap power as described in the page by connecting the C-5203 Power Adapter Harness to the Terminal Block.
    1. Brown and Blue wires are interchangeable and connect to L1and L2.
    2. Secure Green ground wire beneath Green ground screw.
  2. Connect the opposite end of the C-5203 Power Adapter Harness to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID720
KitDescCoin Drop: Factory
  1. Disconnect the Coin Drop from the Machine Control Assembly.
    1. This harness must remain disconnected for FasCard to function properly. Reconnecting this harness after installation will damage the FasCard reader. Technical Support recommends taping off these connections.
  2. Bridge the solid Red and solid Blue wires coming from thecoin eyesensor using the C-5260Wire Tap Bridge.
  3. Bridge the Blue/Silver and solid Purple wires going to themachine control assemblyusing the C-5260Wire Tap Bridge.
  4. Tap the Red, White, and White/Blue wires with the C-5101Spade Taps provided.
  5. Connect the C-6361Coin Sense Harnessto the installed spade taps.
    1. Red connects to Red.
    2. Blue connects to White/Blue.
    3. White connects to White.

Connect Machine Interface Harness

Cci readerinstall kit
KitID661
KitDescPulse
  1. Connect the C-5363 Machine Start Harness to the debit spade connectors on the Machine Control Assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

  1. Feed the remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5363 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-6361 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the Touchscreen Reader Mounting Guide (F2 & F3).
Cci readerinstall footer