Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version 4

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Cci readerinstall kit
KitID917
KitDescCoin and Card

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to F1 FasCard Reader Mounting Guide for further instructions.

Cci readerinstall kit
KitID789
KitDescCard Only - Coin Models

  1. Remove existing coin box and coin drop.

  2. Install C-0963 Drop Cover into the coin drop opening. Secure using C-1062 Keps Nuts.

  3. Bend the side tabs of the C-0936 Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  4. Attach the C-0132 Standoffs to the Bracket.

  5. After connecting harnesses to the reader, attach to C-0936 Bracket using C-0141 Screws.

  6. Optional: Apply C-5027 Label on, or near the reader for any accepted credit card issuers.

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID667
KitDescCard Only - Small Coin Vault

  1. Install the C-5702 Chase Nipple into the C-5414 F2 Mounting Bracketusing the C-5703 Nut.

  2. Feed the remaining harness ends through the open face of the Coin Vault.

  3. Spread the C-6936 Vault Mount Bracket wings outward before insertion to lock bracket into place.

  4. Feed remaining harness ends through the C-6936 Vault Mount Bracket.

  5. Insert the C-6936 Vault Mount Bracket into the Coin Vault.

  6. Feed the remaining harness ends through the combined C-5414 F2 Mounting Bracket.

  7. Secure the combined C-5414 F2 Mounting Bracketto the C-6939 Vault Mount Bracket with the C-0144 Screws.

Cci readerinstall kit
KitID840
KitDescCard Only - Large Coin Vault

  1. Attach the C-5414 F2 Mounting Bracket to the C-6602 Spacer Plate using the C-5702 Chase Nipple and the C-5703 Nut.

  2. Feed the remaining harness ends through the open face of the Coin Vault.

  3. Spread the C-6602 Vault Mount Bracket wings outward before insertion to lock bracket into place.

  4. Feed remaining harness ends through the C-6602 Vault Mount Bracket.

  5. Insert the C-6602 Vault Mount Bracket into the Coin Vault.

  6. Feed the remaining harness ends through the combined C-5414 F2 Mounting Bracket.

  7. Secure the combined C-5414 F2 Mounting Bracketto the C-6602 Vault Mount Bracket with the C-0144 Screws.

Cci readerinstall kit
KitID906
KitDescEasy Card Ready

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Connect Power

Cci readerinstall kit
KitID473

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5338 Power Adapter Harness to the power distribution panel inside the machine or tapping as needed.

    1. 240vac- Connect Blue wire to the L1 tab, and the Brown wire to the L2 tab on the terminal block.

    2. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-5338 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID677
KitDescCoin Drop: Factory Mechanical Switch

  1. Disconnect the factor coin drop harness from the microswitch on the coin drop.

  2. Connect the C-5253 Coin Sense Harness to the microswitch on the the coin drop.

Cci readerinstall kit
KitID679
KitDescCoin Drop: Factory Optical Sensor

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5258 Coin Sense Harness to the harness connected to the Coin Drop.

Cci readerinstall kit
KitID696
KitDescCoin Drop: Imonex w/EM Board

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5382 Coin Sense Harness to the harness connected to the Coin Drop.

Cci readerinstall kit
KitID704
KitDescCoin Drop: Factory - Micro Switch

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.

Cci readerinstall kit
KitID707
KitDescCoin Drop: Factory

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6258 Coin Sense Harness to the harness connected to the Coin Drop.

Cci readerinstall kit
KitID723
KitDescCoin Drop: Factory

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6382 Coin Sense Harness to the harness connected to the Coin Drop.

Cci readerinstall kit
KitID709
KitDescCoin Drop: Imonex Dual Coin

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6261 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID634
KitDescPulse - Optical Sensor

  1. Connect the C-5254 Machine Start Harness to the P2 connector on the Machine Control Assembly.

Cci readerinstall kit
KitID636
KitDescPulse - Micro Switch

  1. Connect the C-5256 Machine Start Harness to the harness previously connected to the coin switch on the Coin Drop.

Connect and Mount Reader

...

Include Page

...

SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

...

  1. If installing C-6261 Coin Sense Harness, connect the secondary connection with the red and orange wires to port 4.

...

_Reader Connections
_Reader Connections

Machine Configuration

No special configuration required.

...