Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version 4

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID906
KitDescCard Only - Rear Control Card Models

  1. Place C-5763 TWL Bracket in the intended mounting location. Using the bracket, mark the location of all four mounting holes.

  2. Drill a hole at each marked location using a 3/16" drill bit.

  3. Attach C-5414 Mounting Bracket to the front of C-5763 using two C-5420 screws.

  4. Mount the C-5763 TLW Bracket using four C-5420 Screws and fasten from the inside of the panel.

Cci readerinstall kit
KitID917
KitDescCoin and Card

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID791
KitDescCard Only - 10 Degree Front Panel Coin Drop Models

  1. Remove existing coin box and coin drop.

  2. Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness.

  3. Install C-5765-W Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.

Cci readerinstall kit
KitID792
KitDescCard Only - Rear Control Coin Drop Models

  1. Remove existing coin box and coin drop.

  2. Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness.

  3. Install C-5762 Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.

Cci readerinstall kit
KitID905
KitDescCard Only - Card Ready Models

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID1026
KitDescCard Only - Rear Control Coin Slide Model

  1. Remove existing coin box and coin slide.

  2. Attach C-5414 Standard Bracket to the C-6762 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.

  3. Insert C-6762 Metercase Bracket into the metercase and secure using C-0301 Topload Mounting Bolt.

Cci readerinstall kit
KitID861
KitDescCard Only - Rear Control Coin Drop Model

  1. Remove the coin drop and coin box.

  2. Remove Vault Switch and bridge the wires previously connected to the Vault Switch with the C-5365 Bypass Harness.

  3. Secure C-5414 F2 Mounting Bracket to the C-6903 Mounting Bracket using the (2)C-5420 10-32 x 1/4 Pan Screws.

  4. Attach the C-5760-A Adapter Bracket to the C-6762 Mounting Bracket to the captured nut on the inside of the C-6762 Mounting Bracket.

  5. Run all reader harnesses through the metercase and out the opening where the coin drop normally mounts.

  6. Run all reader harnesses through the circular opening on the C-6762 Mounting Bracket.

  7. Install the C-6762 Mounting Bracket into the front opening of the metercase so the two threaded posts of the C-5760-A Adapter Bracket line up with the openings for the coin slots. Secure in place using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

Cci readerinstall kit
KitID857
KitDescCard Only - 10° Panel Coin Model

  1. Remove existing coin box and coin drop.

  2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

  3. Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.

  4. Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1Metercase Bracket.

  5. Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

Cci readerinstall kit
KitID1046
KitDescCard Only - Rear Control Coin Slide Models

  1. Remove existing coin box and coin slide.

  2. Install C-5762 Metercase Bracket over the front of the metercase and secure using the C-0301 Mounting Bolt.

Connect Power

Cci readerinstall kit
KitID595
KitDescCoin Slide Models - Tap 120/240v Power

  1. Use the C-5101 Spade Taps on the incoming power.

    1. Tap the L1 wire.

    2. Tap the N wire.

    3. Tap the Ground wire.

  2. Take the C-5210 Power Adapter Harness and connect the red tab connectors to the following wires:

    1. Connect the blue wire to the L1 wire.

    2. Connect the brown wire to the N wire.

    3. Connect the green/yellow wire to the Ground wire.

  3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connection on the C-5602R1 Power Converter.

  4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connection on the C-5500 Power Extension Harness.

Cci readerinstall kit
KitID581
KitDescACA Controls - 12VDC Accessory Power

  1. Connect the C-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly.

    1. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.

Cci readerinstall kit
KitID837
KitDescTitanium Controls - 24VAC Transformer

  1. Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel.

  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID674
KitDescCoin Drop: ACA Control Models

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.

Cci readerinstall kit
KitID677
KitDescCoin Drop: Coin Slide Models

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5253 Coin Sense Harness to the micro switch on the coin slide.

Cci readerinstall kit
KitID700
KitDescCoin Drop - Factory Optical

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Cci readerinstall kit
KitID704
KitDescCoin Slide - Factory Coin Slide Switch

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Slide Switch.

Connect Machine Interface Harness

Cci readerinstall kit
KitID645
KitDescPulse - Coin Connection

  1. Connect the C-5300-NC Machine Start Harness to the harness previously connected to the coin drop.

Cci readerinstall kit
KitID636
KitDescPulse - Coin Slide Switch

  1. Connect the C-5256 Machine Start Harness to the harness previously connected to the Coin Slide Switch.

Cci readerinstall kit
KitID582
KitDescSerial Communication / Serial Pulse

  1. Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly.

Connect and Mount Reader

...

Include Page

...

SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

...

_Reader Connections
_Reader Connections

Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameACA Configuration
PageWithExcerpt_Machine Configuration

...