Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version 4

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Place theC-6700-TEMPDrill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
    Cci readerinstall kit
    KitID584
    KitDescCoin and Card
    Cci readerinstall kit
    KitID906
    KitDescCard Only - Card Model

    1. Remove the (4) security torx retaining screws on the front of the machine.

    2. Remove the soap tray by pulling it out and pressing on the retaining tab in the rear of the tray.

    3. Locate and remove the (2) security torx screws inside the soap tray opening.

    4. Remove the final (2) torx screws to open the top cover.

    5. Locate a spot on top of the machine to mount the reader. Verify included harnesses will reach desired location without encountering interference from internal machine components. Mark the location using C-6700-TEMP Drill Template.

    6. Refer to F2 Reader Mounting Guide for instructions on drilling mounting holes and mounting the reader.

    Cci readerinstall kit
    KitID860
    KitDescCard Only - Coin Model

    1. Remove existing coin box and coin mechanism.

    2. Run reader harnesses through the metercase and out the opening where the coin mechanism was mounted.

    3. Attach the C-5414 Reader Bracket to the C-6911 Metercase Bracket using (2)C-5420 10-32 x 1/4 Pan Screws.

    4. Insert the reader harnesses through the hole in the C-6911 Metercase Bracket and then insert the bracket into the metercase opening.

    5. Secure the C-6911 Metercase Bracket to the metercase using the C-0301 Mounting Bolt.

    Connect Power

    Cci readerinstall kit
    KitID663
    KitDescTap 120v Power

    1. Locate the incoming power cables in the rear of the machine. This should include a white, black and green wire.

    2. Use the C-5101 Spade Taps to tap the black (L1) and white (Neutral) wires.

    3. Attach the spade ends of the C-5336 Power Adapter Harness to the taps. Blue to black, and Brown to White.

    4. Attach the Green ground wire from the C-5336 Power Adapter Harness to a nearby chassis ground screw.

    5. Connect the 3-pin connector from the C-5336 Power Adapter Harness to the 3-pin connector on the C-5602R1 Power Converter.

    6. Connect the 4-pin connector from the C-5602R1 Power Converter to the 4-pin connector on the C-5500 Power Extension Harness.

    7. Mount the C-5602R1Power Converter in the machine by using zip ties to secure it to the machine's wire harness.

    Connect Coin Sense Harness

    Cci readerinstall kit
    KitID721
    KitDescCoin Drop - Factory Optical

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6362 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    Cci readerinstall kit
    KitID1004
    KitDescPulse/Serial - Debit (AA3) Connector

    1. Connect the C-5364 Machine Start Harness to the Debit connector on the Machine Control Assembly.

      1. If needed, use the C-0126-MLV-EXT15 Extension Harness to extend the C-5364 Machine Start Harness.

    Connect and Mount Reader

    ...

    Include Page

    ...

    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    _Reader Connections
    _Reader Connections

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameMayTag Gen1 MLV+ Pulse
    PageWithExcerpt_Machine Configuration

    ...