Versions Compared

Old Version 7

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 8

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to FasCard Mounting Guide for further instructions.
    Cci readerinstall kit
    KitID584
    KitDescCoin and Card
    Cci readerinstall kit
    KitID906
    KitDescCard Only - Rear Control Card Models

    1. Place C-5763 TWL Bracket in the intended mounting location. Using the bracket, mark the location of all four mounting holes.

    2. Drill a hole at each marked location using a 3/16" drill bit.

    3. Attach C-5414 Mounting Bracket to the front of C-5763 using two C-5420 screws.

    4. Mount the C-5763 TLW Bracket using four C-5420 Screws and fasten from the inside of the panel.

    Cci readerinstall kit
    KitID917
    KitDescCoin and Card

    1. Place the C-5700-TEMP Drill Template on the desired mounting location.

    2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

    3. Refer to FasCard Mounting Guide for further instructions.

    Cci readerinstall kit
    KitID791
    KitDescCard Only - 10 Degree Front Panel Coin Drop Models

    1. Remove existing coin box and coin drop.

    2. Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness.

    3. Install C-5765-W Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.

  • Place the C-5700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to FasCard Mounting Guide for further instructions.

  • Remove the coin drop and coin box.

  • Remove Vault Switch and bridge the wires previously connected to the Vault Switch with the C-5365 Bypass Harness.

    • Secure C-5414 F2 Mounting Bracket to the C-6903 Mounting Bracket using the (2)C-5420 10-32 x 1/4 Pan Screws.

  • Attach the C-5760-A Adapter Bracket to the C-6762 Mounting Bracket to the captured nut on the inside of the C-6762 Mounting Bracket.

  • Run all reader harnesses through the metercase and out the opening where the coin drop normally mounts.

  • Run all reader harnesses through the circular opening on the C-6762 Mounting Bracket.

  • Install the C-6762 Mounting Bracket into the front opening of the metercase so the two threaded posts of the C-5760-A Adapter Bracket line up with the openings for the coin slots. Secure in place using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

    • Cci readerinstall kit
    Cci readerinstall kit
    905
    KitID
    KitDescCard Only - Card Ready Models
    Cci readerinstall kit
    KitID861
    KitDescCard Only - Rear Control Coin Drop Model
    KitID857
    KitDescCard Only - 10° Panel Coin Model

    1. Remove existing coin box and coin drop.

    2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

    3. Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.

    4. Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1Metercase Bracket.

    5. Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

    ...

    Cci readerinstall kit
    KitID582
    KitDescSerial Communication / Serial Pulse

    1. Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly.

    Connect and Mount Reader

    ...

    Reader

    ...

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameACA Configuration
    PageWithExcerpt_Machine Configuration

    ...