Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version 4

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID906
KitDescCard Only - Card Models

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID861
KitDescCard Only - Reader Control Coin Models

  1. Remove the coin drop and coin box.

  2. Remove Vault Switch and bridge the wires previously connected to the Vault Switch with the C-5365 Bypass Harness.

  3. Secure C-5414 F2 Mounting Bracket to the C-6903 Mounting Bracket using the (2)C-5420 10-32 x 1/4 Pan Screws.

  4. Attach the C-5760-A Adapter Bracket to the C-6762 Mounting Bracket to the captured nut on the inside of the C-6762 Mounting Bracket.

  5. Run all reader harnesses through the metercase and out the opening where the coin drop normally mounts.

  6. Run all reader harnesses through the circular opening on the C-6762 Mounting Bracket.

  7. Install the C-6762 Mounting Bracket into the front opening of the metercase so the two threaded posts of the C-5760-A Adapter Bracket line up with the openings for the coin slots. Secure in place using the C-1059 Nut and C-1070-W Washer.

Cci readerinstall kit
KitID857
KitDescCard Only - White 10° Panel Coin Models

  1. Remove existing coin box and coin drop.

  2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

  3. Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.

  4. Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1Metercase Bracket.

  5. Install theC-6765-W-R1

Metercase Bracketso that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nutsand (2) C-1070-WWashers.
Cci readerinstall kit
KitID996
KitDescCard Only - Black 10° Panel Coin Models

  • Remove existing coin box and coin drop.

    • Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.Attach theC-5414 F2 Mounting Bracketto the C-6765-B Metercase Bracketusing (2) C-5420 10-32 x 1/4 Pan Screws.Run any card reader harnesses through the coin slot openings and the circular hole in theC-6765-BMetercase Bracket.Install theC-6765-B

    1. Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

    Connect Power

    Cci readerinstall kit
    KitID581
    KitDescACA Controls - 12VDC Accessory Power

    1. Connect the C-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly.

      1. Secure the green wire beneath the ground screw.

    2. Connect the opposite end of the C-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.

    Cci readerinstall kit
    KitID837
    KitDescTitanium Controls - 24VAC Transformer

    1. Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel.

    2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

    Connect Coin Sense Harness

    Cci readerinstall kit
    KitID700
    KitDescCoin Drop - Factory Optical

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6250 Coin Sense Harness to the Coin 1 machine harness connected to the coin drop.

    Cci readerinstall kit
    KitID928
    KitDescCoin Drop - Factory Dual Optical

    1. Disconnect both of the Coin Drops from the Machine Control Assembly.

    2. Connect one of the C-6250 Coin Sense Harness to the Coin 1 machine harness and the other to the Coin 2 machine harness.

    Connect Machine Interface Harness

    Cci readerinstall kit
    KitID582
    KitDescSerial Communication / Serial Pulse

    1. Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    1. Feed remaining harness ends through the mounting hole.

    2. Connect the free end of the C-5240 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

    3. (Coin and Card Installations Only) Connect the free end of the Coin 1 C-6250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    4. (Coin and Card Installations with Factory Dual Optical kits Only) Connect the free end of the Coin 2 C-6250 Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

    5. Connect the free end of the C-6207 or C-6204-40 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameACA Configuration
    PageWithExcerpt_Machine Configuration

    ...