Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Install Mounting Hardware

  • Place the C-5700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

  • Refer to FasCard Mounting Guide for further instructions.
  • Place the C-5700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

  • Refer to FasCard Mounting Guide for further instructions.
    Cci readerinstall kit
    Cci readerinstall kit
    KitID905
    KitDescCard Only - Card Ready
    Cci readerinstall kit
    KitID616
    KitDescCoin and Card
    Cci readerinstall kit
    KitID813
    KitDescCard Only - Coin Ready
    1. Remove coin box and coin slide.

    2. Install C-5771 Metercase Bracket and secure using C-0303 Topload Mounting Bolt.

    KitID614
    KitDescCoin Model
    1. Remove coin box and coin slide.

    2. Install C-5771 Metercase Bracket into the front opening of the metercase and secure using C-0303 Topload Mounting Bolt from the inside.

    3. After running the Cat5e cables and start harness through the front opening of the metercase bracket and connecting them to the LaundryCard reader, use the (2) C-0141 8-32 x 1-1/2" Socket Screws to secure the reader.

    4. Apply the C-0015 Label to the front of the LaundryCard reader around the card slot.

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

  • Refer to FasCard Mounting Guide for further instructions.
  • Remove existing coin box and coin mechanism.

  • Run reader harnesses through the metercase and out the opening where the coin mechanism was mounted.

  • Attach the C-5414 Reader Bracket to the C-6911 Metercase Bracket using (2)C-5420 10-32 x 1/4 Pan Screws.
  • Insert the reader harnesses through the hole in the C-6911 Metercase Bracket and then insert the bracket into the metercase opening.

  • Secure the C-6911 Metercase Bracket to the metercase using the C-0301 Mounting Bolt.

  • Remove the (4) Security T20 retaining screws from the front of the machine.
    Lift up and pull panel forward and lay on machine. NOTE: The front panel may come apart, as it is two parts. Take care not to damage the ribbon cable.
    Mount the C-6980 Mounting Bracket on the front of the panel so that the holes match on the right and the retaining screw on the back of the plate goes through the card slot.
    Place the C-1070-W Washer and C-1042 Keps Nut onto the retaining screw and tighten using 11/32 socket to secure the mounting bracket. The bracket should feel slightly loose until the panel is reattached to the machine.
    cci-readerinstall-kit
    KitID755
    KitDescCard Model
    1. Use the C-0930 Mounting Bracket to mark out the center opening for the card reader and the lower set of holes to the left and right of the central opening.

      1. Ensure the positing leaves enough space for the reader's bezel to sit flat against the machine's panel and for the reader to be inserted into the machine and allow for the CAT5 cables to be connected.

    2. Cut out the central opening and use a 9/64" Drill Bit to make a hole at each drill marks to the left and right of the central opening.

    3. Place the C-0930 Mounting Bracket on the inside of the machine's panel. Pass through and connect the CAT5 cables and machine start harness to the reader.

    4. Use the (2) C-0144 8-32 x 2" Flat Screw to attach the reader to the C-0930 Mounting Bracket.

    5. Apply C-0015 Label over the area around the card slot on the front of the LaundryCard reader.

    Cci readerinstall kit
    KitID584
    KitDescCoin and Card
    Cci readerinstall kit
    KitID860
    KitDescCard Only - Coin Model
    Cci readerinstall kit
    KitID998
    KitDescCard Only - Card Model

    Connect Power

    Connect Coin Sense Harness

    Cci readerinstall kit
    KitID721
    KitDescCoin Drop - Factory Optical
    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6362 Coin Sense Harness to the harness connected to the Coin Drop.

  • Disconnect the Coin Drop from the Machine Control Assembly.

  • Connect the C-5362 Coin Sense Harness to the harness connected to the Coin Drop.
    Cci readerinstall kit
    KitID693
    KitDescCoin Drop: Factory
    step
    componentPower

    Cci readerinstall step
    componentCoin Sense

    Connect Machine Interface Harness

    ...