Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version 4

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Cci readerinstall kit
KitID841
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID851
KitDescCard Only - Coin Ready

  1. Remove Coin Box.

  2. Disconnect harness connection from the Vault Switch. Connect both ends to the C-5365 Bypass Harness.

  3. Spread the C-6936 Vault Mount Bracket wings to lock it into place once installed.

  4. Insert the C-6936 Vault Mount Bracket into the Coin Vault.

  5. Use the C-0144 screws, attach the C-5414 F2 Mounting Bracket to the C-6936 Vault Mount Bracket.

Cci readerinstall kit
KitID846
KitDescCard Only - Card Ready

  1. Install the C-6970R1 Alliance Mounting Bracket into the opening on the control panel for mounting card readers and coin drops.

  2. Attach the C-5414 F2 Mounting Bracket to the C-6970 Alliance Mounting Bracket and secure using the C-1060 Screws.

Connect Power

Cci readerinstall kit
KitID1020

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  2. Connect the opposite end of the C-5210 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500-115 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID700
KitDescCoin Drop: Factory

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID645
KitDescPulse

  1. Connect the C-5300-NC Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.

Cci readerinstall kit
KitID603
KitDescSerial

  1. Connect the C-0110-TOP Machine Start Harness to the H3 connector on the Machine Control Assembly.

...

The following steps assume the start and coin sense harnesses are already connected to the upper pocket control.

Locate area to mountC-6411Serial Stack Add-On Board.
  1. Must be close enough to reader mounting location to connect the harness to.
  2. Must be on a surface that does not received direct exposure from any heating elements (If applicable.)
  • Clean mounting location to remove any dust and residue if needed.
    • Remove the sticker from the back of the C-6411Serial Stack Add-On Boardto expose the adhesive and apply to the mounting location.Connect the white, 7-pin connector from theC-0110-TOP to the H3connection on the lower pocket's Machine Control Assembly.Connect the the clear, 3-pin circuit board end from theC-6250-144 Coin Sense Harnessto the lower pocket's Coin Drop.

    The following steps assume the start and coin sense harnesses are already connected to the upper pocket control.

    Locate area to mountC-6411Serial Stack Add-On Board.
    1. Must be close enough to reader mounting location to connect the harness to.
    2. Must be on a surface that does not received direct exposure from any heating elements (If applicable.)
  • Clean mounting location to remove any dust and residue if needed.
    • Remove the sticker from the back of the C-6411Serial Stack Add-On Boardto expose the adhesive and apply to the mounting location.Connect the white, 7-pin connector from theC-0110-TOP to the H3connection on the lower pocket's Machine Control Assembly.Apply the C-5033 Label over the coin drop opening for the lower pocket.
    cci-readerinstall-kitstep
    KitID1068
    KitDescPulse and Serial - Card Only (Card Ready Models)
    1. Run C-0110-TOP-144 Machine Start Harness to the second Machine Control Assembly.
    2. Connect C-0110-TOP-144 Machine Start Harness to the H3 connection on the second Machine Control Assembly.
    3. Connect the C-6401 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
      1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Unit 1 on the Stack Add-on Board.
      2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Unit 2 on the Stack Add-on Board.
    Cci readerinstall kit
    KitID1072
    KitDescPulse and Serial - Card unsafe-Only (Card Ready Models)
    Cci readerinstall kit
    KitID1078
    KitDescSerial - Card Only (Card Ready Models)
    componentExtras

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    1. Feed remaining harness ends through the mounting holes.

    2. (Standard Installations - No Stack Add-On Kit) Connect the free end of the Machine Start Harness:

      1. If following steps for a serial, connect the C-0110-TOP Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

      2. If following steps for a pulse, connect the C-5300-NC Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    3. (F2/F3 - Serial Stack Add-On Installations Only) Connect the black, 10-pin connector from the C-0110-TOP Machine Start Harness to the Unit 1 connection and the C-0110-TOP Machine Start Harness to the Unit 2 connection on the C-6401 or C-6411 Serial Stack Add-On Board.

    4. (Coin and Card Installations Only) Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    5. Connect the free end of the C-5500-115 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

    6. Secure the FasCard reader to base as described in the F2 Reader Mounting Guide.

    Cci readerinstall footer