Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version 4

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to

for further instructions.
Cci readerinstall kit
KitID667
KitDescCard Only
Install theC-5702Chase Nippleinto theC-5414F2 Mounting Bracketusing theC-5703Nut.Feed the remaining harness ends through the open face of theCoin Vault.Spread theC-6936Vault Mount Bracketwings outward before insertion to lock bracket into place.Feed remaining harness ends through theC-6936Vault Mount Bracket.Insert theC-6936Vault Mount Bracketinto theCoin Vault.Feed the remaining harness ends through the combinedC-5414F2 Mounting Bracket.Secure the combinedC-5414F2 Mounting Bracketto theC-6939 Vault Mount Bracket with theC-0144Screws.

  1. FasCard Mounting Guide for further instructions.

Connect Power

Cci readerinstall kit
KitID473

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5338 Power Adapter Harness to the power distribution panel inside the machine or tapping as needed.

    1. 120vac- Connect Brown and Blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac- Connect Brown and Blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-5338 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID704
KitDescCoin Drop: Factory

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.

Cci readerinstall kit
KitID723
KitDescCoin Drop: Imonex

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6382 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID636
KitDescPulse

  1. Connect the C-5256 Machine Start Harness to the factory coin drop harness previously connected to the microswitch.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

Item No.

Component

Notes

1

Power Connection Port

Utilizes the same power harnesses as the first generation FasCard reader.

2

Pulse Connection Port

Connection point for pulse machine start harnesses.

3

Coin 1 Connection Port

This is the connection point for the harness input associated with Coin 1.

4

Coin 2 Connection Port

This is the connection point for the harness input associated with Coin 2.

5

Serial Connection Port

This is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the F2: FasCard Reader Mounting Guide.

  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  4. Connect the free end of the C-5500 Power Harness to port 1.

  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

...