Versions Compared

Old Version 7

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 8

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Cci readerinstall kit
KitID841
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID945
KitDescCard Only

  1. Place the C-5414 Mounting Bracket on top of the C-6601 Spacer Plate.

  2. Place both Mounting Bracket and Spacer Plate over the mounting hole previously used by the coin drop.

  3. Place the C-6701 Adapter Plate on the opposite side of the machine panel and secure in place using the C-5416 Screws.

  4. Place the C-5710 Rubber Grommet into the circular opening of the C-5414 Mounting Bracket.

Connect Power

Cci readerinstall kit
KitID595

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

...

Cci readerinstall kit
KitID935
KitDescPulse

  1. Run C-5344 Machine Start Harness and C-6348 Coin Sense Harness to the second Machine Control Assembly.

  2. Connect C-5344 Machine Start Harness to the Coin 1 connection and the C-6348 Coin Sense Harness to the coin drop for the second Machine Control Assembly.

  3. Connect the C-6400 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.

    1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Port 2 on the reader.

    2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to the Stack Add-on Board.

  4. Connect the Coin Sense Harness connected to the upper pocket Coin Drop to port 3 (Coin 1 Sense Harness Connection Port) on the F2 reader.

  5. Connect the Coin Sense Harness connected to the lower pocket Coin Drop to port 4 (Coin 2 Sense Harness Connection Port) on the F2 reader.

Connect and Mount Reader

Expand
titleF1 Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF1 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole as described in F1: FasCard Reader Mounting Guide.

  2. Connect the free end of the C-5344 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. Connect the free end of the C-5343 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  4. Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

  5. Secure the FasCard reader to base as described in the F1: FasCard Reader Mounting Guide.

Expand
titleF2, F3, Flex, FlexRF

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.

  2. Connect the free end of the C-5344 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. Connect the free end of the C-6348 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  4. Connect the free end of the C-5500 Power Harness to port 1.

  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

...

Cci readerinstall step
componentReader

Cci readerinstall footer