Versions Compared

Old Version 30

changes.mady.by.user Former user

Saved on

compared with

New Version 31

changes.mady.by.user Former user

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Overview

Multiexcerpt
MultiExcerptNameOverview

This document is intended to guide the user through installation utilizing the kit numbered according to the document title. A list of associated equipment models including control information and additional installation notes can be found below.

Install Header

Multiexcerpt
MultiExcerptNameInstall Header
mediumnote

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

C-5001falsefalse

F2 Install Header

Multiexcerpt
MultiExcerptNameF2 Install Header
mediumnote

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Required Hardware

Card Reader

C-5401falsefalse

Reader Ports

Multiexcerpt
MultiExcerptNameReader ports

F2 Reader Ports

Multiexcerpt
MultiExcerptNameF2 Reader Ports

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.


Additional Info

Multiexcerpt
MultiExcerptNameAdditional Info
trueINLINE

Additional Information

Unverified

Multiexcerpt
MultiExcerptNameUnverified
largewarning

These instructions and kit hardware have not been verified or tested by Card Concepts Inc. and are used at the installers own risk.

ACA Dip Switches

Multiexcerpt
MultiExcerptNameACA Dip Switches

ACA machines using a serial configuration require dip switch 3 on the Machine Control Assembly to be set to the 'ON' position. All other dip switches should remain in the 'OFF' position.

ACA Card Ready

Multiexcerpt
MultiExcerptNameACA Card Ready

ACA Card Ready machines using a pulse configuration require a retrofit to a Coin-Ready state. This may require obtaining an additional Coin Sense Harness from Alliance.

Multiexcerpt
MultiExcerptNameTools
Description
Link/Source
Image
Champion CT7-1-1/8 Tungsten Carbide Tipped
1-1/8-Inch Hole Cutter-1-Inch Thick Metal
(Or Equivalent)

Amazon

Cutting OilAmazon

9/64" Drill Bit (Optional)
If drilling stainless steel should be rated for 
such
(Or Equivalent)

Amazon
Heavy Duty Professional 3/8" Magnesium Drill
with #2 drill tip extension.
(Or Equivalent)		Harbor Freight
Center Punch
(Or Equivalent)		Amazon
HammerAmazon
Fine Point Sharpie Marker
(Or Equivalent)		Amazon
Pliers
(Or Equivalent)		Amazon
Tape MeasureAmazon
C-5700-TEMP  FasCard Drill Template
*Included in C-1490 Kit 		CCI