Versions Compared

Old Version 1

changes.mady.by.user Brett Norrell

Saved on

compared with

New Version Current

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID616
KitDescCoin and Card

  1. Place theC-5700-TEMPDrill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID818
KitDescCard Only

  1. Remove existing coin box.

  2. Bend the side tabs of theC-0936 Vault Bracketoutward and install into the coin vault. The tabs should snap into place securing the bracket.

  3. Attach the C-0133 Standoffs to the Bracket.

  4. Attach reader to the Bracket using C-0141 Screw.

Connect Power

Cci readerinstall kit
KitID807

  1. Tap power as described in the document by connecting theC-5101Power Adapter Harnessto the power distribution panel inside the machine.

    1. 120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of theC-5101Power Adapter Harnessto theC-5602Power Converter.

  3. Connect theC-5500-84Power Extension Harness to the appropriate connector on theC-5602Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID689
KitDescCoin Drop: Edge Connector
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5357 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID690
KitDescCoin Drop: Terminal Connection
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5358 Coin Sense Harness to the harness connected to the Coin Drop.
    1. Match each of the colored wires from the coin drop to the matching wire on the coin sense harness.

Connect Machine Interface Harness

Cci readerinstall kit
KitID655
KitDescPulse - Edge Connection
  1. Connect the C-5353R1 Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.
Cci readerinstall kit
KitID830
KitDescPulse - Terminal Connection with Block
  1. Attach the C-5313 Terminal Block to the Machine Control Assembly.
  2. Connect the C-5356 Machine Start Harness to the Positions 2 and 3 on the C-5313 Terminal Block.
    1. Terminal block positions are numbered 0-6. Position 0 is closest to the board edge.
Cci readerinstall kit
KitID659
KitDescPulse - Terminal Connection without Block
  1. Connect the C-5356 Machine Start Harness to Position 2 and 3 on the coin connection terminal on the Machine Control Assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF1 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole as described in F1: FasCard Reader Mounting Guide.
  2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-84 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the F1: FasCard Reader Mounting Guide.

Machine Configuration

TODO

Cci readerinstall footer