Versions Compared

Old Version 2

changes.mady.by.user Adam Arafat

Saved on

compared with

New Version Current

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID569
KitDescCoin and Card

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID789
KitDescCard Only

  1. Remove existing coin box and coin drop.

  2. Install C-0963 Drop Coverwhere the coin drop was previously. Secure using C-1062 Kep Nuts.

  3. Bend the side tabs of theC-0936 Bracketoutward and install into the coin vault. The tabs should snap into place securing the bracket.

  4. Attach C-0132 Standoffsto C-0936 Bracket.
  5. After running harnesses and connecting them to the reader, attach the reader to C-0936 Bracketusing C-0141 Screws.
  6. Optional: Apply C-5027 Labelon or near the reader for any accepted credit card issuers.

Connect Power

Cci readerinstall kit
KitID473
  1. Tap power as described in the document by connecting theC-5338Power Adapter Harness to the power distribution panel inside the machine or tapping as needed.
    1. 120vac- Connect Brown and Blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.
    2. 240vac- Connect Brown and Blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.
    3. Secure the green wire beneath the ground screw.
  2. Connect the opposite end of theC-5338 Power Adapter Harnessto theC-5602 Power Converter.
  3. Connect theC-5500 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID677
KitDescCoin Drop: Microswitch
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5253 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID696
KitDescCoin Drop: Imonex with EM100/EM3
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5382 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID636
KitDescPulse
  1. Connect theC-5256 Machine Start Harness to thefactory coin drop harnesspreviously connected to the microswitch.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF1 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole as described in F1: FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the F1: FasCard Reader Mounting Guide.

Machine Configuration

TODO

Cci readerinstall footer