Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
    cci-readerinstall-kitstep
    KitID584
    KitDescCoin and Card
    componentMounting

    Install theC-0961 Jam Ring into the coin vault. TheJam Ringshould be installed into the coin vault so that it is within 1.5" of front panel of the machine to allow the mounting bracket to be attached.To install theJam Ringinsert the ring so the small portion is on the bottom. Insert at an angle, so the top of theJam Ringis inserted first. Once the ring is in position, pull the top of theJam Ringtowards the front of the machine until it locks into place.Using theC-5751Screws, attach theC-6960Mounting Bracketto theC-0961Jam Ring.
  • Attach the C-5414 Standard Mounting Bracket to the C-6960 Mounting Bracket using the C-5420 Screws.
    • cci-readerinstall-kit
    KitID872
    KitDescCard Only

    ...

    step
    componentPower

    Tap power as described in the document by connecting the C-5210 Power Adapter Harness to the power distribution panel inside the machine.

    1. 120vac: Connect the blue wire to L1 and the brown wire to N.

    2. 240vac: Connect the blue wire to L1 and the brown wire to L2.

    3. Connect the green wire to the ground wire..

  • Connect the opposite end of the C-5210 Power Adapter Harness to the C-5602R1 Power Converter.

  • Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

    • cci-readerinstall-kit
    KitID595

    ...

    step
    componentCoin Sense

    cci-readerinstall-kitstep
    KitIDcomponent704
    KitDescCoin Drop: Factory
    1. Disconnect the Coin Drop from the Machine Control Assembly.
    2. Connect the C-6253 Coin Sense Harness to the Microswitch on the coin drop.

    Connect Machine Interface Harness

    Start

    cci-readerinstall-kit
    KitID636
    KitDescPulse
    1. Connect the C-5256 Machine Start Harness to the Coin Drop Coin Harness connected to the machine control assembly.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    1. Feed remaining harness ends through the mounting hole as described in the Touchscreen Reader Mounting Guide (F2 & F3).
    2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
    3. Connect the free end of the C-6253 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
    4. Connect the free end of the C-5500 Power Harness to port 1.
    5. Secure the FasCard reader to base as described in the Touchscreen Reader Mounting Guide (F2 & F3).

    Machine Configuration

    ...

    step
    componentReader

    Cci readerinstall footer