Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Place theC-6700-TEMPDrill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
    cci-readerinstall-kitstep
    KitID584
    KitDescCoin and Card
    componentMounting

    Remove the (4) security torx retaining screws on the front of the machine.
    Remove the soap tray by pulling it out and pressing on the retaining tab in the rear of the tray.
    Locate and remove the (2) security torx screws inside the soap tray opening.
    Remove the final (2) torx screws to open the top cover.
    Locate a spot on top of the machine to mount the reader.Verify included harnesses will reach desired location without encountering interference from internal machine components. Mark the location using C-6700-TEMP Drill Template.Refer to for instructions on drilling mounting holes and mounting the reader.

  • Remove existing coin box and coin mechanism.

  • Run reader harnesses through the metercase and out the opening where the coin mechanism was mounted.

    • Attach the C-5414 Reader Bracketto the C-6911 Metercase Bracketusing(2)C-542010-32 x 1/4 Pan Screws.Insert the reader harnesses through the hole in the C-6911 Metercase Bracketand then insert the bracket into the metercase opening.Secure the C-6911 Metercase Bracket to the metercase using the C-0301Mounting Bolt.
    cci-readerinstall-kit
    KitID906
    KitDescCard Only - Card Model
    Cci readerinstall kit
    KitID860
    KitDescCard Only - Coin Model

    ...

    step
    componentPower

    Locate the incoming power cables in the rear of the machine. This should include a white, black and green wire.
    Use the C-5101 Spade Tapsto tap the black (L1) and white (Neutral) wires.
    Attach the spade ends of the C-5336 Power Adapter Harnessto the taps. Blue to black, and Brown to White.
    Attach the Green ground wire from the C-5336 Power Adapter Harnessto a nearby chassis ground screw.
    Connect the 3-pin connector from the C-5336 Power Adapter Harness to the 3-pin connector on the C-5602R1 Power Converter.
    Connect the 4-pin connector from the C-5602R1 Power Converter to the 4-pin connector on the C-5500Power Extension Harness.
    Mount the C-5602R1Power Converterin the machine by using zip ties to secure it to the machine's wire harness.
    cci-readerinstall-kitstep
    KitID663
    KitDescTap 120v Power

    ...

    componentCoin Sense

  • Disconnect the Coin Drop from the Machine Control Assembly.
    • Connect theC-6362 Coin Sense Harness to the harness connected to the Coin Drop.
    cci-readerinstall-kitstep
    KitID721
    KitDescCoin Drop - Factory Optical

    Connect Machine Interface Harness

    componentStart

    Connect theC-5364 Machine Start Harness to theDebit connector on the Machine Control Assembly.If needed, use the C-0126-MLV-EXT15 Extension Harnessto extend the C-5364 Machine Start Harness.
    cci-readerinstall-kit
    KitID1004
    KitDescPulse/Serial - Debit (AA3) Connector

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    step
    componentReader

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameMayTag Gen1 MLV+ Pulse
    PageWithExcerpt_Machine Configuration

    ...