Install Mounting Hardware
| cci-readerinstall-kit |
|---|
| KitID | 584 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to for further instructions.| Cci readerinstall kit |
|---|
| KitID | 867 |
|---|
| KitDesc | Card Only - Coin Prepped Models |
|---|
|
Secure the mounting bracket from the C-5414 F2 Mounting Bracket to the C-6601Spacer Plate using the C-5702Chase Nipple and the C-5703 Nut.Feed the remaining harness ends through the open face of theCoin Vault.Spread the C-6602 Vault Mount Bracketwings outward before insertion to lock bracket into place.Feed remaining harness ends through the C-6602Vault Mount Bracket.Insert the C-6602Vault Mount Bracketinto theCoin Vault.Feed the remaining harness ends through the combined C-5414F2 Mounting Bracketand C-6601Filler Plate.Secure thecombined C-5414 F2 Mounting Bracket and C-6601 Filler Plate to the C-6602 Vault Mount Bracket with the C-0144 Screws.Install the C-0963Drop Cover over the cavity left by theCoin Drop and secure with C-1062 Kep Nuts.
Connect Power
...
...
120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.
240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.
Secure the green wire beneath the ground screw.
...
Connect the opposite end of the C-5338 Power Adapter Harness to the C-5602 Power Converter.
...
Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
Connect Coin Sense Harness
| Cci readerinstall kit |
|---|
| KitID | 704 |
|---|
| KitDesc | Coin Drop: Factory - Micro Switch |
|---|
|
- Disconnect the Coin Drop from the Machine Control Assembly.
- Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 707 |
|---|
| KitDesc | Coin Drop: Factory - Optical Sensor |
|---|
|
- Disconnect the Coin Drop from the Machine Control Assembly.
- Connect the C-6258 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 709 |
|---|
| KitDesc | Coin Drop: Factory - Imonex |
|---|
|
- Disconnect the Coin Drop from the Machine Control Assembly.
- Connect the C-6261 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 723 |
|---|
| KitDesc | Coin Drop: Aftermarket - Imonex |
|---|
|
- Disconnect the Coin Drop from the Machine Control Assembly.
- Connect the C-6382 Coin Sense Harness to the harness connected to the Coin Drop.
|
Connect Machine Interface Harness
| Cci readerinstall kit |
|---|
|
- Connect the C-5254 Machine Start Harness to the P2 connector on the Machine Control Assembly.
|
| Cci readerinstall kit |
|---|
|
- Connect the C-0127-MLV Machine Start Harness to the P23 connector on the Machine Control Assembly.
|
Connect and Mount Reader
| Multiexcerpt include |
|---|
| SpaceWithExcerpt | CCIDOC |
|---|
| MultiExcerptName | F2 Reader |
|---|
| PageWithExcerpt | _Reader Ports |
|---|
|
...
Machine Configuration
...