Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Place theC-6700-TEMPDrill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.

  • Remove existing coin box and coin drop.

    • Secure C-5414 F2 Mounting Bracketto the C-6903Mounting Bracket using the (2)C-542010-32 x 1/4 Pan Screws.Install theC-6903Mounting Bracketinto theCoin Vault. Use (4) C-1042Kep Nuts to secure toCoin Vault.
    cci-readerinstall-kit
    KitID584
    KitDescCoin and Card
    Cci readerinstall kit
    KitID845
    KitDescCard Only - 30lb or Larger Model
    step
    componentMounting

  • Remove existing coin box and coin drop.

    • Secure C-5414 F2 Mounting Bracketto the C-6902 Mounting Bracket using the (2)C-542010-32 x 1/4 Pan Screws.Install theC-6902Mounting Bracketinto theCoin Vault. Use (4) C-1042Kep Nuts to secure toCoin Vault.
    cci-readerinstall-kit
    KitID868
    KitDescCard Only - 20lb Model

    ...

    step
    componentPower

    Tap power as described in the document using theC-5101 Spade Taps provided.Connect theC-5336 Power Adapter Harness to the installed spade taps. Connect the opposite end to theC-5602 Power Converter.
    1. Secure the ground wire beneath a chassis screw.
    Connect theC-5500 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.
    cci-readerinstall-kit
    KitID663
    KitDescTap 120/240v Power

    ...

    step
    componentCoin Sense

  • Disconnect the Coin Drop from the Machine Control Assembly.
    • Connect theC-6332 Coin Sense Harness to the harness connected to the Coin Drop.Connect the Redconnector to the Coin Acceptorconnection, where the coin drop was previously connected, on the Machine Control Assembly.
    cci-readerinstall-kitstep
    KitID923
    KitDescCoin Drop - Factory Optical
    Cci readerinstall kit
    KitID885
    KitDescCombination Harness - Coin Sense Connections
    1. Disconnect the Coin Drop from the Machine Control Assembly.
    2. Connect the white, male, 8-pin connector from the C-6330 Combination Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

  • Connect the C-0114-MLV Machine Start Harness to the middle X1 port on the serial communication board.
    • The RJ11 connector on the end of the C-0114-MLV Machine Start Harness will fit into the middle X1 RJ45 port even though the RJ11 connectoris smaller in size.CCIDOCCOM Boardsfalse
    Cci readerinstall kit
    KitID608
    KitDescSerial
    componentStart

    Connect the red, female, 8-pin connector of the C-6330 Combination Harness to the Coin Acceptorconnector on the Machine Control Assembly.
    cci-readerinstall-kit
    KitID885
    KitDescPulse - Combination Harness - Machine Interface Connections

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    step
    componentReader

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameContinental ProfitPlus
    PageWithExcerpt_Machine Configuration

    ...