Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
  • Remove Coin Box.
  • Disconnect harness connection from the Vault Switch. Connect both ends to the C-5365 Bypass Harness.
  • Spread the C-6936 Vault Mount Bracket wings to lock it into place once installed.
  • Insert the C-6936 Vault Mount Bracket into the Coin Vault.
    • Use the C-0144 screws, attach the C-5414 F2 Mounting Bracketto the C-6936Vault Mount Bracket.
    cci-readerinstall-kit
    KitID841
    KitDescCoin and Card
    Cci readerinstall kit
    KitID851
    KitDescCard Only - Coin Ready
    step
    componentMounting

    Install the C-6970R1Alliance Mounting Bracket into the opening on the control panel for mounting card readers and coin drops.Attach the C-5414 F2 Mounting Bracket to the C-6970Alliance Mounting Bracketand secure using the C-1060Screws.
    cci-readerinstall-kit
    KitID846
    KitDescCard Only - Card Ready

    ...

    step
    componentPower

    Tap power as described in the document using the C-5101 Spade Taps provided.
  • Connect the opposite end of the C-5210 Power Adapter Harness to the C-5602 Power Converter.
  • Connect the C-5500-115 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
    • cci-readerinstall-kitstep
    KitID1020

    ...

    componentCoin Sense

    cci-readerinstall-kit
    KitID700
    KitDescCoin Drop: Factory
    1. Disconnect the Coin Drop from the Machine Control Assembly.
    2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    Connect the C-5300-NC Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.
    Cci readerinstall kit
    KitID645
    KitDescPulse
    step
    componentStart

    cci-readerinstall-kitstep
    KitID603
    KitDescSerial
    1. Connect the C-0110-TOP Machine Start Harness to the H3 connector on the Machine Control Assembly.

    Optional: Stack Add-On Installation

    componentExtras

    The following steps assume the start and coin sense harnesses are already connected to the upper pocket control.

    Locate area to mountC-6411Serial Stack Add-On Board.
    1. Must be close enough to reader mounting location to connect the harness to.
    2. Must be on a surface that does not received direct exposure from any heating elements (If applicable.)
  • Clean mounting location to remove any dust and residue if needed.
    • Remove the sticker from the back of the C-6411Serial Stack Add-On Boardto expose the adhesive and apply to the mounting location.Connect the white, 7-pin connector from theC-0110-TOP to the H3connection on the lower pocket's Machine Control Assembly.Connect the the clear, 3-pin circuit board end from theC-6250-144 Coin Sense Harnessto the lower pocket's Coin Drop.

    The following steps assume the start and coin sense harnesses are already connected to the upper pocket control.

    Locate area to mountC-6411Serial Stack Add-On Board.
    1. Must be close enough to reader mounting location to connect the harness to.
    2. Must be on a surface that does not received direct exposure from any heating elements (If applicable.)
  • Clean mounting location to remove any dust and residue if needed.
    • Remove the sticker from the back of the C-6411Serial Stack Add-On Boardto expose the adhesive and apply to the mounting location.Connect the white, 7-pin connector from theC-0110-TOP to the H3connection on the lower pocket's Machine Control Assembly.
  • Apply the C-5033 Label over the coin drop opening for the lower pocket.
    • cci-readerinstall-kit
    KitID1068
    KitDescPulse and Serial - Card Only (Card Ready Models)
    1. Run C-0110-TOP-144 Machine Start Harness to the second Machine Control Assembly.
    2. Connect C-0110-TOP-144 Machine Start Harness to the H3 connection on the second Machine Control Assembly.
    3. Connect the C-6401 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
      1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Unit 1 on the Stack Add-on Board.
      2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Unit 2 on the Stack Add-on Board.
    Cci readerinstall kit
    KitID1072
    KitDescPulse and Serial - Card unsafe-Only (Card Ready Models)
    Cci readerinstall kit
    KitID1078
    KitDescSerial - Card Only (Card Ready Models)

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    step
    componentReader

    Cci readerinstall footer