Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.Install the C-6970Alliance Mounting Bracketinto the opening on the control panel for mounting card readers and coin drops.Attach the C-5414F2 Mounting Bracket to the C-6970R1Alliance Mounting Bracket and secure using the C-1060Screws.Refer to for further instructions.
    cci-readerinstall-kit
    KitID584
    KitDescCoin and Card
    Cci readerinstall kit
    KitID846
    KitDescCard Only - ACA Card Ready
    step
    componentMounting

  • Remove existing coin box and coin drop.

    • Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

  • Bend the side tabs of the C-6936 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  • Place the C-5710 Rubber Grommet into the circular opening of the C-6936 Vault Bracket.

  • Align the C-5414 F2 Mounting Bracket over the coin vault opening and then attach the to the C-6936 Vault Bracket using the (2) C-0144 screws.

  • Apply C-5033 Label over coin drop opening.
    • (Coin Model Only) Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

  • Remove factory payment device bay cover or card reader mounting plate.

  • Place the C-6976 Quantum Touch Stk Dryer Mounting Bracket into the payment device opening and secure using the (4) C-107310-24 Hex Nut.

  • Align the C-5414 F2 Mounting Bracket with the C-6976 Quantum Touch Stk Dryer Mounting Bracket and attach using the (2) C-5420 10-32 x 1/4" Screws.

    • cci-readerinstall-kit
    KitID844
    KitDescCard Only - Coin Ready
    Cci readerinstall kit
    KitID988
    KitDescCard Only - Quantum Touch Control

    ...

    step
    componentPower

    Connect theC-6204-40 Power Adapter Harness (12VDC power) to the H10 connection on the Machine Control Assembly.

  • Secure the green wire beneath the ground screw.

    • Tap power as described in the document using the C-5101 Spade Taps provided.
  • Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602R1 Power Converter.
  • Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.
    • cci-readerinstall-kit
    KitID581
    Cci readerinstall kit
    KitID794

    ...

    step
    componentCoin Sense

    cci-readerinstall-kit
    KitID700
    KitDescCoin Drop: Factory
    1. Disconnect the Coin Drop from the Machine Control Assembly.
    2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    Cci readerinstall kit
    KitID582
    KitDescPulse or Serial
    1. Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.

    ...

    step
    componentStart

    cci-readerinstall-kitstep
    KitIDcomponent927
    KitDescPulse and Serial - Coin and Card
    1. Run C-5240-144 Machine Start Harness and C-6250-144 Coin Sense Harness to the second Machine Control Assembly.
    2. Connect C-5240-144 Machine Start Harness to the H3 connection and the C-6250-144 Coin Sense Harness to the Coin 1 connection on the second Machine Control Assembly.
    3. Connect the C-6401 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
      1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Unit 1 on the Stack Add-on Board.
      2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Unit 2 on the Stack Add-on Board.
    4. Connect the Coin Sense Harness connected to the upper pocket Coin Drop to port 3 (Coin 1 Sense Harness Connection Port) on the F2 reader.
    5. Connect the Coin Sense Harness connected to the lower pocket Coin Drop to port 4 (Coin 2 Sense Harness Connection Port) on the F2 reader.
    Extras

    cci-readerinstall-kit
    KitID957
    KitDescPulse and Serial - Card Only (Coin Ready Models)
    1. Install C-0940 Vault Cover into the coin vault for the secondary control.
    2. Run C-5240-144 Machine Start Harness to the second Machine Control Assembly.
    3. Connect C-5240-144 Machine Start Harness to the H3 connection on the second Machine Control Assembly.
    4. Connect the C-6401 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
      1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Unit 1 on the Stack Add-on Board.
      2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Unit 2 on the Stack Add-on Board.
    Cci readerinstall kit
    KitID960
    KitDescPulse and Serial - Card Only (Card Ready Models)
    1. Run C-5240-144 Machine Start Harness to the second Machine Control Assembly.
    2. Connect C-5240-144 Machine Start Harness to the H3 connection on the second Machine Control Assembly.
    3. Connect the C-6401 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
      1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Unit 1 on the Stack Add-on Board.
      2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Unit 2 on the Stack Add-on Board.
    Cci readerinstall kit
    KitID1061
    KitDescF3 Reader - Pulse/Serial - Coin and Card

    The following steps assume the start and coin sense harnesses are already connected to the upper pocket control.

    1. Locate area to mount C-6411 Serial Stack Add-On Board.
      1. Must be close enough to reader mounting location to connect the harness to.
      2. Must be on a surface that does not received direct exposure from any heating elements (If applicable.)
    2. Clean mounting location to remove any dust and residue if needed.
    3. Remove the sticker from the back of the C-6411 Serial Stack Add-On Board to expose the adhesive and apply to the mounting location.
    4. Connect the white, 7-pin connector from the C-5240-144 to the H3 connection on the lower pocket's Machine Control Assembly.
    5. Connect the the clear, 3-pin circuit board end from the C-6250-144 Coin Sense Harness to the lower pocket's Coin Drop.
    Cci readerinstall kit
    KitID1067
    KitDescF3 Reader - Pulse/Serial - Coin and Card

    The following steps assume the start and coin sense harnesses are already connected to the upper pocket control.

    1. Locate area to mount C-6411 Serial Stack Add-On Board.
      1. Must be close enough to reader mounting location to connect the harness to.
      2. Must be on a surface that does not received direct exposure from any heating elements (If applicable.)
    2. Clean mounting location to remove any dust and residue if needed.
    3. Remove the sticker from the back of the C-6411 Serial Stack Add-On Board to expose the adhesive and apply to the mounting location.
    4. Connect the white, 7-pin connector from the C-5240-144 to the H3 connection on the lower pocket's Machine Control Assembly.
    5. Optional: Apply C-5033 Label over the card reader opening for the lower pocket control.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    step
    componentReader

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameACA Configuration
    PageWithExcerpt_Machine Configuration

    ...