Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
    cci-readerinstall-kitstep
    KitID841
    KitDescCoin and Card
    componentMounting

  • Remove existing coin box.

    • Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.Bend the side tabs of theC-0941Vault Coveroutward and install into the coin vault. The tabs should snap into place securing the bracket.Place theC-6700-TEMPDrill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.Place theC-6700-TEMPDrill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
    cci-readerinstall-kit
    KitID906
    KitDescCard Only - Coin Ready
    Cci readerinstall kit
    KitID912
    KitDescCard Only - Card Ready

    ...

    step
    componentPower

    Connect theC-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly.

    1. Secure the green wire beneath the ground screw.

    Connect the opposite end of theC-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.
    cci-readerinstall-kit
    KitID581

    ...

    step
    componentCoin Sense

    cci-readerinstall-kitstep
    KitID700
    KitDescCoin Drop: Factory
    1. Disconnect the Coin Drop from the Machine Control Assembly.
    2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    componentStart

    cci-readerinstall-kitstep
    KitID582
    KitDescSerial or Pulse
    1. Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.

    Optional: Stack Add-on Installation

    componentExtras

    cci-readerinstall-kitstep
    KitID938
    KitDescPulse and Serial
    1. Run C-5240 Machine Start Harness and C-6250 Coin Sense Harness to the second Machine Control Assembly.
    2. Connect C-5240 Machine Start Harness to the H3 connection and the C-6250 Coin Sense Harness to the Coin 1 connection on the second Machine Control Assembly.
    3. Connect the C-6401 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
      1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Unit 1 on the Stack Add-on Board.
      2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to Unit 2 on the Stack Add-on Board.
    4. Connect the Coin Sense Harness connected to the upper pocket Coin Drop to port 3 (Coin 1 Sense Harness Connection Port) on the F2 reader.
    5. Connect the Coin Sense Harness connected to the lower pocket Coin Drop to port 4 (Coin 2 Sense Harness Connection Port) on the F2 reader.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    componentReader

    Machine Configuration

    ACA machines using a serial configuration require dip switch 3 on the Machine Control Board to be set to the 'ON' position. Leave all other dip switches as is.

    ...