Versions Compared

Old Version 4

changes.mady.by.user Chris Kite

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-5700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID616
    KitDescCoin and Card
    step
    componentMounting

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify that included harnesses will reach the desired location without encountering interference from internal machine components.

    • Refer to FasCard Mounting Guide for further instructions.

  • Remove existing coin drop.

  • Install C-0913 Drop Cover where the coin drop was previously mounted. Secure using (4) C-1062 4-40 Keps Nuts.

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify that included harnesses will reach the desired location without encountering interference from internal machine components.

    • Refer to Touchscreen Reader Mounting Guide (F2 & F3) for further instructions.

  • Optional: Use C-5710 Rubber Grommet to protect harnesses from damage during machine operation if any secondary hole is cut internally to run harnesses to the reader mounting location.

    • cci-readerinstall-kit
    KitID841
    KitDescCoin and Card
    Cci readerinstall kit
    KitID959
    KitDescCard Only

    ...

    step
    componentPower

    Tap power as described in the FasCard Reader Install - Universal Concepts page by connecting the C-5203 Power Adapter Harness to the Terminal Block.

    1. Brown and Blue wires are interchangeable and connect to L1 and L2.

    2. Secure Green ground wire beneath Green ground screw.

  • Connect the opposite end of the C-5203 Power Adapter Harness to the C-5602 Power Converter.

  • Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

    • cci-readerinstall-kit
    KitID804

    ...

    step
    componentCoin Sense

    cci-readerinstall-kitstep
    KitID692
    KitDescCoin Drop: Factory

    1. Disconnect the Coin Drop from the Machine Control Assembly.

      1. This harness must remain disconnected for FasCard to function properly. Reconnecting this harness after installation will damage FasCard reader. Technical Support recommends taping off these connections.

    2. Bridge the solid Red and solid Blue wires coming from the coin eye sensor using the C-5260 Wire Tap Bridge.

    3. Bridge the Blue/Silver and solid Purple wires going to the machine control assembly using the C-5260 Wire Tap Bridge.

    4. Tap the Red, White, and White/Blue wires with the C-5101 Spade Taps provided.

    5. Connect the C-5361 Coin Sense Harness to the installed spade taps.

      1. Red connects to Red.

      2. Blue connects to White/Blue.

      3. White connects to White.

    componentStart

    cci-readerinstall-kitstep
    KitID720
    KitDescCoin Drop: Factory

    1. Disconnect the Coin Drop from the Machine Control Assembly.

      1. This harness must remain disconnected for FasCard to function properly. Reconnecting this harness after installation will damage the FasCard reader. Technical Support recommends taping off these connections.

    2. Bridge the solid Red and solid Blue wires coming from the coin eye sensor using the C-5260 Wire Tap Bridge.

    3. Bridge the Blue/Silver and solid Purple wires going to the machine control assembly using the C-5260 Wire Tap Bridge.

    4. Tap the Red, White, and White/Blue wires with the C-5101 Spade Taps provided.

    5. Connect the C-6361 Coin Sense Harness to the installed spade taps.

      1. Red connects to Red.

      2. Blue connects to White/Blue.

      3. White connects to White.

    Connect Machine Interface Harness

    Cci readerinstall kit
    KitID661
    KitDescPulse

    1. Connect the C-5363 Machine Start Harness to the debit spade connectors on the Machine Control Assembly.

    Connect and Mount Reader

    ...

    componentReader

    Cci readerinstall footer