| cci-readerinstall-kit |
|---|
| KitID | 755 |
|---|
| KitDesc | Card Model |
|---|
|
Use the C-0930 Mounting Bracket to mark out the center opening for the card reader and the lower set of holes to the left and right of the central opening. Ensure the positing leaves enough space for the reader's bezel to sit flat against the machine's panel and for the reader to be inserted into the machine and allow for the CAT5 cables to be connected.
Cut out the central opening and use a 9/64" Drill Bit to make a hole at each drill marks to the left and right of the central opening. Place the C-0930 Mounting Bracket on the inside of the machine's panel. Pass through and connect the CAT5 cables and machine start harness to the reader. Use the (2) C-0144 8-32 x 2" Flat Screw to attach the reader to the C-0930 Mounting Bracket. Apply C-0015 Label over the area around the card slot on the front of the LaundryCard reader.
|
| Cci readerinstall kit |
|---|
| KitID | 584 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.| Cci readerinstall kit |
|---|
| KitID | 860 |
|---|
| KitDesc | Card Only - Coin Model |
|---|
|
Remove existing coin box and coin mechanism.
Run reader harnesses through the metercase and out the opening where the coin mechanism was mounted.
Attach the C-5414 Reader Bracket to the C-6911 Metercase Bracket using (2)C-5420 10-32 x 1/4 Pan Screws.Insert the reader harnesses through the hole in the C-6911 Metercase Bracket and then insert the bracket into the metercase opening.
Secure the C-6911 Metercase Bracket to the metercase using the C-0301 Mounting Bolt.
| Cci readerinstall kit |
|---|
| KitID | 998 |
|---|
| KitDesc | Card Only - Card Model |
|---|
|
Remove the (4) Security T20 retaining screws from the front of the machine.
Lift up and pull panel forward and lay on machine. NOTE: The front panel may come apart, as it is two parts. Take care not to damage the ribbon cable.
Mount the C-6980 Mounting Bracket on the front of the panel so that the holes match on the right and the retaining screw on the back of the plate goes through the card slot.
Place the C-1070-W Washer and C-1042 Keps Nut onto the retaining screw and tighten using 11/32 socket to secure the mounting bracket. The bracket should feel slightly loose until the panel is reattached to the machine.
...
| cci-readerinstall-kit |
|---|
| KitID | 999 |
|---|
| KitDesc | Tap 120v Power |
|---|
|
Locate the 120v power lines in the machine. These wires are usually black and white and are located just inside the back of the panel. Use a voltage tester to confirm the correct wiring.
Apply the C-5101 Spade Taps to both the black and white power wires and clamping them down with pliers.
Plug the brown wire of the C-5336 Power Adapter Harness to the white/neutral wire tap and the blue wire to the black/L1 wire tap.
Locate a green chassis ground screw and loosen to insert the green wire from the C-5336 Power Adapter Harness and retighten.
Connect the 3-pin connector from the C-5336 Power Adapter Harness to the C-5602R1 Power Converter.
Apply the C-1098 Velcro to the C-5602R1 Power Converter and secure inside the machine's panel.
Connect the 4-pin connector from the C-5500 Power Extension Harness to the C-5602R1 Power Converter.
Route the 3-pin connector from the C-5500 Power Extension Harness through the open card slot on the machine control panel.
...
...
...