Versions Compared

Old Version 4

changes.mady.by.user Chris Kite

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID584
    KitDescCoin and Card

    Connect Power

    step
    componentMounting

    Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5338 Power Adapter Harness to the power distribution panel inside the machine.

    1. 120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

  • Connect the opposite end of the C-5338 Power Adapter Harness to the C-5602 Power Converter.

  • Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

    • cci-readerinstall-kitstep
    KitID473

    Connect Coin Sense Harness

    componentPower

  • Disconnect the Coin Drop from the Machine Control Assembly.

    • Connect the C-6253 Coin Harness to the harness connected to the Coin Drop.
    cci-readerinstall-kitstep
    704
    KitIDcomponentKitDescCoin Drop: Factory - Micro Switch
    Sense

    cci-readerinstall-kit
    KitID707
    KitDescCoin Drop: Factory - Optical Sensor

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6258 Coin Sense Harness to the harness connected to the Coin Drop.

    Cci readerinstall kit
    KitID709
    KitDescCoin Drop: Factory - Imonex

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6261 Coin Sense Harness to the harness connected to the Coin Drop.

    Cci readerinstall kit
    KitID723
    KitDescCoin Drop: Aftermarket - Imonex

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6382 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    Connect the C-5254 Machine Start Harness to the P2 connector on the Machine Control Assembly.
    Cci readerinstall kit
    KitID634
    KitDescPulse
    step
    componentStart

    cci-readerinstall-kit
    KitID578
    KitDescSerial

    1. Connect the C-0127-MLV Machine Start Harness to the P23 connector on the Machine Control Assembly.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    Item No.

    Component

    Notes

    1

    Power Connection Port

    Utilizes the same power harnesses as the first generation FasCard reader.

    2

    Pulse Connection Port

    Connection point for pulse machine start harnesses.

    3

    Coin 1 Connection Port

    This is the connection point for the harness input associated with Coin 1.

    4

    Coin 2 Connection Port

    This is the connection point for the harness input associated with Coin 2.

    5

    Serial Connection Port

    This is the connection point for serial machine start harnesses.

    1. Feed remaining harness ends through the mounting hole as described in the FasCard Mounting Guide.

    2. Connect the free end of the Machine Start Harness.

      1. If following steps for a serial Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

      2. If following steps for a pulse Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    4. Connect the free end of the Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

    5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

    Machine Configuration

    ...

    step
    componentReader

    Cci readerinstall footer