Versions Compared

Old Version 4

changes.mady.by.user Chris Kite

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID584
    KitDescCoin and Card

    Connect Power

    step
    componentMounting

    Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5338 Power Adapter Harness to the power distribution panel inside the machine or tapping as needed.

    1. 120vac- Connect Brown and Blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac- Connect Brown and Blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

  • Connect the opposite end of the C-5338 Power Adapter Harness to the C-5602 Power Converter.

  • Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

    • cci-readerinstall-kitstep
    KitID473

    Connect Coin Sense Harness

    componentPower

  • Disconnect the Coin Drop from the Machine Control Assembly.

    • Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.
    cci-readerinstall-kit
    KitID704
    KitDescCoin Drop: Factory
    step
    componentCoin Sense

    cci-readerinstall-kitstep
    KitIDcomponent723
    KitDescCoin Drop: Imonex

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6382 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    Start

    cci-readerinstall-kit
    KitID636
    KitDescPulse

    1. Connect the C-5256 Machine Start Harness to the factory coin drop harness previously connected to the microswitch.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    Item No.

    Component

    Notes

    1

    Power Connection Port

    Utilizes the same power harnesses as the first generation FasCard reader.

    2

    Pulse Connection Port

    Connection point for pulse machine start harnesses.

    3

    Coin 1 Connection Port

    This is the connection point for the harness input associated with Coin 1.

    4

    Coin 2 Connection Port

    This is the connection point for the harness input associated with Coin 2.

    5

    Serial Connection Port

    This is the connection point for serial machine start harnesses.

    1. Feed remaining harness ends through the mounting hole as described in the F2: FasCard Reader Mounting Guide.

    2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    4. Connect the free end of the C-5500 Power Harness to port 1.

    5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

    Machine Configuration

    ...

    step
    componentReader

    Cci readerinstall footer