Install Mounting Hardware
| cci-readerinstall-kit |
|---|
| KitID | 584 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.| step |
|---|
|
|
| cci-readerinstall-kit |
|---|
| KitID | 906 |
|---|
| KitDesc | Card Only - Card Models |
|---|
|
Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.| Cci readerinstall kit |
|---|
| KitID | 861 |
|---|
| KitDesc | Card Only - Reader Control Coin Models |
|---|
|
Remove the coin drop and coin box.
Remove Vault Switch and bridge the wires previously connected to the Vault Switch with the C-5365 Bypass Harness.
Secure C-5414 F2 Mounting Bracket to the C-6903 Mounting Bracket using the (2)C-5420 10-32 x 1/4 Pan Screws.Attach the C-5760-A Adapter Bracket to the C-6762 Mounting Bracket to the captured nut on the inside of the C-6762 Mounting Bracket.
Run all reader harnesses through the metercase and out the opening where the coin drop normally mounts.
Run all reader harnesses through the circular opening on the C-6762 Mounting Bracket.
Install the C-6762 Mounting Bracket into the front opening of the metercase so the two threaded posts of the C-5760-A Adapter Bracket line up with the openings for the coin slots. Secure in place using the C-1059 Nut and C-1070-W Washer.
| Cci readerinstall kit |
|---|
| KitID | 857 |
|---|
| KitDesc | Card Only - White 10° Panel Coin Models |
|---|
|
Remove existing coin box and coin drop.
Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.
Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1Metercase Bracket.Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.
...
| cci-readerinstall-kit |
|---|
| KitID | 581 |
|---|
| KitDesc | ACA Controls - 12VDC Accessory Power |
|---|
|
Connect the C-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly. Secure the green wire beneath the ground screw.
Connect the opposite end of the C-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.
|
| Cci readerinstall kit |
|---|
| KitID | 837 |
|---|
| KitDesc | Titanium Controls - 24VAC Transformer |
|---|
|
Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
|
...
| cci-readerinstall-kitstep |
|---|
| KitID | 700 |
|---|
| KitDesc | Coin Drop - Factory Optical |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-6250 Coin Sense Harness to the Coin 1 machine harness connected to the coin drop.
|
|
|
| cci-readerinstall-kit |
|---|
| KitID | 928 |
|---|
| KitDesc | Coin Drop - Factory Dual Optical |
|---|
|
Disconnect both of the Coin Drops from the Machine Control Assembly. Connect one of the C-6250 Coin Sense Harness to the Coin 1 machine harness and the other to the Coin 2 machine harness.
|
Connect Machine Interface Harness
| Cci readerinstall kit |
|---|
| KitID | 582 |
|---|
| KitDesc | Serial Communication / Serial Pulse |
|---|
|
Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.
|
Connect and Mount Reader
| Multiexcerpt include |
|---|
| SpaceWithExcerpt | CCIDOC |
|---|
| MultiExcerptName | F2 Reader |
|---|
| PageWithExcerpt | _Reader Ports |
|---|
|
...
Feed remaining harness ends through the mounting hole.
...
Connect the free end of the C-5240 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
...
(Coin and Card Installations Only) Connect the free end of the Coin 1 C-6250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
...
(Coin and Card Installations with Factory Dual Optical kits Only) Connect the free end of the Coin 2 C-6250 Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.
...
Machine Configuration
| Multiexcerpt include |
|---|
| SpaceWithExcerpt | CCIDOC |
|---|
| MultiExcerptName | ACA Configuration |
|---|
| PageWithExcerpt | _Machine Configuration |
|---|
|
...