Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

  • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID584
    KitDescCoin and Card
    step
    componentMounting

  • Remove existing coin box and coin drop.

  • Bridge the Coin Vault Switch connections using C-5365 Bypass Harness.

  • Attach C-5760-A Alliance Adapter Bracket to C-6762 Metercase Bracket.

  • Attach the C-5414 Mounting Bracket to C-6762 Metercase Bracket using the (2)C-5420 10-32 x 1/4 Pan Screws.
  • Mount C-6762 Metercase Bracket into the front of the metercase, inserting the two studs through the coin slot openings.

    1. Secure to the metercase using (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

  • Remove existing coin box and coin drop.

  • Attach C-5760-A Alliance Adapter Bracket to C-6760 Metercase Bracket.

  • Attach the C-5414 Mounting Bracket to C-6760 Metercase Bracket using the (2)C-5420 10-32 x 1/4 Pan Screws.
  • Mount C-6760 Metercase Bracket into the front of the metercase, inserting the two studs through the coin slot openings.

    1. Secure to the metercase using (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

  • cci-readerinstall-kit
    KitID861
    KitDescCard Only - Coin Model w/ High Capacity Metercase
    Cci readerinstall kit
    KitID916
    KitDescCard Only - Coin Model w/ Standard Metercase

    ...

    step
    componentPower

    cci-readerinstall-kit
    KitID581
    KitDescACA Control - 12VDC Accessory Power
    1. Connect the C-6204-40 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.

      1. Connect the green wire to a chassis ground.

    2. The remaining end (3-pin molex) connects directly to the rear of the F2 Reader.

    Cci readerinstall kit
    KitID837
    KitDescTitanium Control - 24VAC Transformer
    1. Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel.

    2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

    ...

    KitID663
    KitDescTap 120v Machine Power

    ...

    1. 120vac: Connect the blue wire to L1 and the brown wire to N.

    2. 240vac: Connect the blue wire to L1 and the brown wire to L2.

    3. Secure the green wire to the ground screw.

    ...

    Connect the opposite end of the C-5336 Power Adapter Harness to the C-5602R1 Power Converter.

    ...

    Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

    ...

    step
    componentCoin Sense

    cci-readerinstall-kit
    KitID700
    KitDescCoin Drop - Factory Optical
    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

    Cci readerinstall kit
    KitID704
    KitDescCoin Slide - Factory Switch
    1. Disconnect the harness from micro switch.

    2. Connect both ends of C-6253 Coin Sense Harness to the micro switch.

    Connect Machine Interface Harness

    Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly.
    Cci readerinstall kit
    KitID582
    KitDescSerial / Pulse - ACA/Titanium Control
    step
    componentStart

    cci-readerinstall-kit
    KitID636
    KitDescPulse - Hybrid Coin Slide Control
    1. Connect the C-5256 Machine Start Harness to the manufacturer's harness previously connected to the micro switch used by the coin slide.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    Feed remaining harness ends through the mounting hole.

    ...

    (Hybrid Coin Slide Controls Only) Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    ...

    (ACA/Titanium Controls Only) Connect the free end of the C-5240 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

    ...

    (Coin and Card Install Only) Connect the free end of the C-6250 or C-6253 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    ...

    step
    componentReader

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameACA Configuration
    PageWithExcerpt_Machine Configuration

    ...