Versions Compared

Old Version 4

changes.mady.by.user Chris Kite

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID584
    KitDescCoin and Card
    step
    componentMounting

  • Install the C-6970 Alliance Mounting Bracket into the opening on the control panel for mounting card readers and coin drops.

  • Attach the C-5414 F2 Mounting Bracket to the C-6970R1 Alliance Mounting Bracket and secure using the C-1060 Screws.

    • Refer to F2/F3 FasCard Reader Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID846
    KitDescCard Only - ACA Card Ready
    Cci readerinstall kit
    KitID844
    KitDescCard Only - Coin Ready

    1. Remove existing coin box and coin drop.

    2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

    3. Bend the side tabs of the C-6936 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

    4. Place the C-5710 Rubber Grommet into the circular opening of the C-6936 Vault Bracket.

    5. Align the C-5414 F2 Mounting Bracket over the coin vault opening and then attach the to the C-6936 Vault Bracket using the (2) C-0144 screws.

    6. Apply C-5033 Label over coin drop opening.

    Cci readerinstall kit
    KitID988
    KitDescCard Only - Quantum Touch Control

    1. (Coin Model Only) Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

    2. Remove factory payment device bay cover or card reader mounting plate.

    3. Place the C-6976 Quantum Touch Stk Dryer Mounting Bracket into the payment device opening and secure using the (4) C-107310-24 Hex Nut.

    4. Align the C-5414 F2 Mounting Bracket with the C-6976 Quantum Touch Stk Dryer Mounting Bracket and attach using the (2) C-5420 10-32 x 1/4" Screws.

    ...

    step
    componentPower

    Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  • Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602R1 Power Converter.

  • Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

    • cci-readerinstall-kit
    KitID581

    1. Connect the C-6204-40 Power Adapter Harness (12VDC power) to the H10 connection on the Machine Control Assembly.

    2. Secure the green wire beneath the ground screw.

    Cci readerinstall kit
    KitID794

    ...

    step
    componentCoin Sense

    cci-readerinstall-kit
    KitID700
    KitDescCoin Drop: Factory

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.
    Cci readerinstall kit
    KitID582
    KitDescPulse or Serial
    step
    componentStart

    Cci readerinstall step
    componentExtras

    ...