Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-5700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

  • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID616
    KitDescCoin and Card
    step
    componentMounting

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

  • Refer to FasCard Mounting Guide for further instructions.
  • Apply C-5035 Label over the coin drop opening.

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

  • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID841
    KitDescCoin and Card
    Cci readerinstall kit
    KitID966
    KitDescCard Only

    ...

    step
    componentPower

    Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  • Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  • Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

  • cci-readerinstall-kit
    KitID595

    ...

    step
    componentCoin Sense

    cci-readerinstall-kitstep
    KitIDcomponent695
    KitDescCoin Drop: Factory
    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-5368 Coin Sense Harness to the harness connected to the Coin Drop.

    Start

    cci-readerinstall-kit
    KitID722
    KitDescCoin Drop: Factory
    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6368 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    Cci readerinstall kit
    KitID653
    KitDescPulse
    1. Connect the C-5345 Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    Item No.

    Component

    Notes

    1

    Power Connection Port

    Utilizes the same power harnesses as the first generation FasCard reader.

    2

    Pulse Connection Port

    Connection point for pulse machine start harnesses.

    3

    Coin 1 Connection Port

    This is the connection point for the harness input associated with Coin 1.

    4

    Coin 2 Connection Port

    This is the connection point for the harness input associated with Coin 2.

    5

    Serial Connection Port

    This is the connection point for serial machine start harnesses.

    1. Feed remaining harness ends through the mounting hole as described in the F2,F3 Reader Install Guide.

    2. Connect the free end of the C-5345 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    3. Connect the free end of the C-6368 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    4. Connect the free end of the C-5500 Power Harness to port 1.

    5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

    Machine Configuration

    ...

    step
    componentReader

    Cci readerinstall footer