Versions Compared

Old Version 4

changes.mady.by.user David Bussman

Saved on

compared with

New Version Current

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID917
KitDescCoin and Card

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID789
KitDescCard Only - Coin Models

  1. Remove existing coin box and coin drop.

  2. Install C-0963 Drop Cover into the coin drop opening. Secure using C-1062 Keps Nuts.

  3. Bend the side tabs of the C-0936 Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  4. Attach the C-0132 Standoffs to the Bracket.

  5. After connecting harnesses to the reader, attach to C-0936 Bracket using C-0141 Screws.
  6. Optional: Apply C-5027 Label on, or near the reader for any accepted credit card issuers.

Connect Power

Cci readerinstall kit
KitID473
  1. Tap power as described in the document by connecting theC-5338Power Adapter Harness to the power distribution panel inside the machine or tapping as needed.
    1. 240vac- Connect Blue wire to the L1 tab, and the Brown wire to the L2 tab on the terminal block.
    2. Secure the green wire beneath the ground screw.
  2. Connect the opposite end of theC-5338 Power Adapter Harnessto theC-5602 Power Converter.
  3. Connect theC-5500 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID677
KitDescCoin Drop: Factory Mechanical Switch
  1. Disconnect the factor coin drop harness from the microswitch on the coin drop.
  2. Connect the C-5253 Coin Sense Harness to the microswitch on the the coin drop.
Cci readerinstall kit
KitID679
KitDescCoin Drop: Factory Optical Sensor
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5258 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID696
KitDescCoin Drop: Imonex w/EM Board
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5382 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID636
KitDescPulse - Mechanical Switch
  1. Connect the C-5256 Machine Start Harness to the factory coin harness previously connected to the micro switch on the coin drop.
Cci readerinstall kit
KitID634
KitDescPulse - Optical Coin Sensor
  1. Connect the C-5254 Machine Start Harness to the P2 connector on the Machine Control Assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF1 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole as described in F1: FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5254 or C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. (Coin and Card Installation Only) Connect the free end of the C-5253, C-5258, or C5382 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the F1: FasCard Reader Mounting Guide.
Cci readerinstall footer