Versions Compared

Old Version 5

changes.mady.by.user Chris Kite

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-5700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID616
    KitDescCoin and Card
    step
    componentMounting

  • Remove existing coin box.

  • Insert the C-5710 Rubber Grommet into the central hole of the C-6936 Vault Bracket.

  • Run all reader harnesses through coin vault and then the hole of the C-6936 Vault Bracket.

  • Bend the side tabs of the C-6936 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  • Run all reader harnesses through the central hole of the C-5414 Reader Bracket.

    • Attach the C-5414 Reader Bracket to the C-6936 Vault Bracketusing the C-0144 screw.
    cci-readerinstall-kitstep
    KitID992
    KitDescCard Only

    Connect Power

    ...

    componentPower

  • Disconnect the Coin Drop from the Machine Control Assembly.

    • Connect the C-5258 Coin Sense Harness to the harness connected to the Coin Drop.
    cci-readerinstall-kit
    KitID679
    KitDescFactory - Optical Coin Drop
    step
    componentCoin Sense

    cci-readerinstall-kitstep
    KitID707
    KitDescCoin Drop: Factory

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6258 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    componentStart

    cci-readerinstall-kitstep
    KitID578
    KitDescSerial

    1. Connect the C-0127-MLV Machine Start Harness to the P9 - Serial connection on the Machine Control Assembly.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    Item No.

    Component

    Notes

    1

    Power Connection Port

    Utilizes the same power harnesses as the first generation FasCard reader.

    2

    Pulse Connection Port

    Connection point for pulse machine start harnesses.

    3

    Coin 1 Connection Port

    This is the connection point for the harness input associated with Coin 1.

    4

    Coin 2 Connection Port

    This is the connection point for the harness input associated with Coin 2.

    5

    Serial Connection Port

    This is the connection point for serial machine start harnesses.

    1. Feed remaining harness ends through the mounting hole as described in the Touchscreen Reader Mounting Guide (F2 & F3).

    2. Connect the free end of the C-0127-MLV Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

    3. Connect the free end of the C-6258 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    4. Connect the free end of the C-5500-115 Power Harness to port 1.

    5. Secure the FasCard reader to base as described in the Touchscreen Reader Mounting Guide (F2 & F3).

    Machine Configuration

    ...

    componentReader

    Cci readerinstall footer