Versions Compared

Old Version 5

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.

  • Remove existing coin box and coin drop.

    • Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.Attach theC-5414 F2 Mounting Bracketto the C-6765-W-R1 Metercase Bracketusing C-5702 Chase Nippleand C-5703 Lock Nut.Run any card reader harnesses through the coin slot openings and the circular hole in theC-6765-W-R1Metercase Bracket.Install the C-6765-W-R1Metercase Bracketso that the two threaded posts insert into the coin drop slots. Then secure it to the machine using theC-1059 Kep Nutsand C-1070-WWashers.

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
    cci-readerinstall-kit
    KitID584
    KitDescCoin and Card
    Cci readerinstall kit
    KitID857
    KitDescCard Only - 10° Panel Coin Models
    Cci readerinstall kit
    KitID906
    KitDescCard Only - All Card Models

    ...

    step
    componentMounting

    Cci readerinstall step
    componentPower

    Connect the 2-pin connector from theC-6207 F2, ACA Power Harnessto the 24v transformer behind the front control panel.
  • The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
    • Tap power as described in the document using theC-5101 Spade Taps provided.Connect theC-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to theC-5602 Power Converter.Connect theC-5500 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.
    cci-readerinstall-kitstep
    KitID581
    KitDescACA Controls
    1. Connect the C-6204-40 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.
    2. Connect the green wire to a chassis ground.
    3. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
    Cci readerinstall kit
    KitID837
    KitDescTitanium Controls
    Cci readerinstall kit
    KitID595
    KitDescHybrid Coin Slides

    ...

    componentCoin Sense

  • Disconnect the Coin Drop from the Machine Control Assembly.
    • Connect theC-6250 Coin Sense Harness to the harness connected to the Coin Drop.
    cci-readerinstall-kit
    KitID700
    KitDescFactory Standard Coin Drop
    Cci readerinstall kit
    KitID704
    KitDescFactory Standard Coin Slide
    1. Locate the micro switch on the coin slide assembly for the upper pocket.
    2. Disconnect the harness connected to the microswitch and connect C-6253 Coin Sense Harness to the spade tabs on the micro switch.

    Connect Machine Interface Harness

    Connect theC-5300-NC Machine Start Harness to theCoin 1 connector on the Machine Control Assembly.
    Cci readerinstall kit
    KitID645
    KitDescPulse - Coin Connection
    step
    componentStart

    Connect theC-5240 Machine Start Harness to the the H3connection on the Machine Control Assembly or Communication board.
    cci-readerinstall-kitstep
    KitID582
    KitDescSerial Communication / Serial Pulse
    componentExtras

    Connect theC-5256 Machine Start Harness to the the harness previously connected to the coin slide microswitch spade tabs.
    cci-readerinstall-kitstep
    KitID636
    KitDescHybrid Coin Slide Switch

    Connect Stack Add-On Components

    ...

    KitID1023
    KitDescSerial Stack Add-On - Card Only - Card Models

    ...

    KitID938
    KitDescSerial Stack Add-On - Coin and Card Install

    ...

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    1. If installing a Stack Add-On kit with a coin and card setup, connect the C-6250 Coin Sense Harness from the lower pocket's coin drop to Port 4 (Coin Sense 2 Harness Connection Port) as shown in the image above.

    ...

    componentReader

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameACA Configuration
    PageWithExcerpt_Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameTitanium Configuration (Small Dryer)
    PageWithExcerpt_Machine Configuration

    Cci readerinstall footer