Install Mounting Hardware
| cci-readerinstall-kit |
|---|
| KitID | 584 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.| step |
|---|
|
|
| cci-readerinstall-kit |
|---|
| KitID | 906 |
|---|
| KitDesc | Card Only - Rear Control Card Models |
|---|
|
Place C-5763 TWL Bracket in the intended mounting location. Using the bracket, mark the location of all four mounting holes.
Drill a hole at each marked location using a 3/16" drill bit.
Attach C-5414 Mounting Bracket to the front of C-5763 using two C-5420 screws.
Mount the C-5763 TLW Bracket using four C-5420 Screws and fasten from the inside of the panel.
| Cci readerinstall kit |
|---|
| KitID | 917 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-5700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.
| Cci readerinstall kit |
|---|
| KitID | 791 |
|---|
| KitDesc | Card Only - 10 Degree Front Panel Coin Drop Models |
|---|
|
Remove existing coin box and coin drop. Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness. Install C-5765-W Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.
|
| Cci readerinstall kit |
|---|
| KitID | 792 |
|---|
| KitDesc | Card Only - Rear Control Coin Drop Models |
|---|
|
Remove existing coin box and coin drop. Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness. Install C-5762 Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.
|
...
| KitID | 905 |
|---|
| KitDesc | Card Only - Card Ready Models |
|---|
...
Place the C-5700-TEMP Drill Template on the desired mounting location.
...
Verify included harnesses will reach desired location without encountering interference from internal machine components.
...
| Cci readerinstall kit |
|---|
| KitID | 1026 |
|---|
| KitDesc | Card Only - Rear Control Coin Slide Model |
|---|
|
Remove existing coin box and coin slide. Attach C-5414 Standard Bracket to the C-6762 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws. Insert C-6762 Metercase Bracket into the metercase and secure using C-0301 Topload Mounting Bolt.
|
...
| KitID | 861 |
|---|
| KitDesc | Card Only - Rear Control Coin Drop Model |
|---|
...
Remove the coin drop and coin box.
...
Remove Vault Switch and bridge the wires previously connected to the Vault Switch with the C-5365 Bypass Harness.
...
Attach the C-5760-A Adapter Bracket to the C-6762 Mounting Bracket to the captured nut on the inside of the C-6762 Mounting Bracket.
...
Run all reader harnesses through the metercase and out the opening where the coin drop normally mounts.
...
Run all reader harnesses through the circular opening on the C-6762 Mounting Bracket.
...
Install the C-6762 Mounting Bracket into the front opening of the metercase so the two threaded posts of the C-5760-A Adapter Bracket line up with the openings for the coin slots. Secure in place using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.
...
| KitID | 857 |
|---|
| KitDesc | Card Only - 10° Panel Coin Model |
|---|
...
Remove existing coin box and coin drop.
...
Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
...
Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.
...
Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.
| Cci readerinstall kit |
|---|
| KitID | 1046 |
|---|
| KitDesc | Card Only - Rear Control Coin Slide Models |
|---|
|
Remove existing coin box and coin slide. Install C-5762 Metercase Bracket over the front of the metercase and secure using the C-0301 Mounting Bolt.
|
...
| cci-readerinstall-kit |
|---|
| KitID | 595 |
|---|
| KitDesc | Coin Slide Models - Tap 120/240v Power |
|---|
|
Use the C-5101 Spade Taps on the incoming power. Tap the L1 wire. Tap the N wire. Tap the Ground wire.
Take the C-5210 Power Adapter Harness and connect the red tab connectors to the following wires: Connect the blue wire to the L1 wire. Connect the brown wire to the N wire. Connect the green/yellow wire to the Ground wire.
Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connection on the C-5602R1 Power Converter. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connection on the C-5500 Power Extension Harness.
|
| Cci readerinstall kit |
|---|
| KitID | 581 |
|---|
| KitDesc | ACA Controls - 12VDC Accessory Power |
|---|
|
Connect the C-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly. Secure the green wire beneath the ground screw.
Connect the opposite end of the C-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.
|
| Cci readerinstall kit |
|---|
| KitID | 837 |
|---|
| KitDesc | Titanium Controls - 24VAC Transformer |
|---|
|
Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
|
...
| cci-readerinstall-kit |
|---|
| KitID | 674 |
|---|
| KitDesc | Coin Drop: ACA Control Models |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 677 |
|---|
| KitDesc | Coin Drop: Coin Slide Models |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-5253 Coin Sense Harness to the micro switch on the coin slide.
|
| Cci readerinstall kit |
|---|
| KitID | 700 |
|---|
| KitDesc | Coin Drop - Factory Optical |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 704 |
|---|
| KitDesc | Coin Slide - Factory Coin Slide Switch |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Slide Switch.
|
Connect Machine Interface Harness
| Cci readerinstall kit |
|---|
| KitID | 645 |
|---|
| KitDesc | Pulse - Coin Connection |
|---|
|
Connect the C-5300-NC Machine Start Harness to the harness previously connected to the coin drop.| step |
|---|
|
|
| cci-readerinstall-kit |
|---|
| KitID | 636 |
|---|
| KitDesc | Pulse - Coin Slide Switch |
|---|
|
Connect the C-5256 Machine Start Harness to the harness previously connected to the Coin Slide Switch.
|
| Cci readerinstall kit |
|---|
| KitID | 582 |
|---|
| KitDesc | Serial Communication / Serial Pulse |
|---|
|
Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly.
|
Connect and Mount Reader
...
Machine Configuration
| Multiexcerpt include |
|---|
| SpaceWithExcerpt | CCIDOC |
|---|
| MultiExcerptName | ACA Configuration |
|---|
| PageWithExcerpt | _Machine Configuration |
|---|
|
...