Versions Compared

Old Version 6

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-5700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
    cci-readerinstall-kit
    KitID616
    KitDescCoin and Card
    Cci readerinstall kit
    KitID841
    KitDescCoin and Card
    Cci readerinstall kit
    KitID945
    KitDescCard Only

    1. Place the C-5414 Mounting Bracket on top of the C-6601 Spacer Plate.

    2. Place both Mounting Bracket and Spacer Plate over the mounting hole previously used by the coin drop.
    3. Place the C-6701 Adapter Plate on the opposite side of the machine panel and secure in place using the C-5416 Screws.
    4. Place the C-5710 Rubber Grommet into the circular opening of the C-5414 Mounting Bracket.

    Connect Power

    ...

    KitID595

    ...

    Connect Coin Sense Harness

    Cci readerinstall kit
    KitID685
    KitDescCoin Drop: Factory
    1. Disconnect the Coin Drop from the Machine Control Assembly.
    2. Connect the C-5343 Coin Sense Harness to the harness connected to the Coin Drop.
    Cci readerinstall kit
    KitID713
    KitDescCoin Drop: Factory
    1. Disconnect the Coin Drop from the Machine Control Assembly.
    2. Connect the C-6348 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    Cci readerinstall kit
    KitID652
    KitDescPulse
    1. Connect the C-5344 Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

    Optional: Stack Add-on Installation

    Cci readerinstall kit
    KitID935
    KitDescPulse
    1. Run C-5344 Machine Start Harness and C-6348 Coin Sense Harness to the second Machine Control Assembly.
    2. Connect C-5344 Machine Start Harness to the Coin 1 connection and the C-6348 Coin Sense Harness to the coin drop for the second Machine Control Assembly.
    3. Connect the C-6400 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.
      1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Port 2 on the reader.
      2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to the Stack Add-on Board.
    4. Connect the Coin Sense Harness connected to the upper pocket Coin Drop to port 3 (Coin 1 Sense Harness Connection Port) on the F2 reader.
    5. Connect the Coin Sense Harness connected to the lower pocket Coin Drop to port 4 (Coin 2 Sense Harness Connection Port) on the F2 reader.

    Connect and Mount Reader

    Expand
    titleF1 Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF1 Reader
    PageWithExcerpt_Reader Ports

    1. Feed remaining harness ends through the mounting hole as described in F1: FasCard Reader Mounting Guide.
    2. Connect the free end of the C-5344 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
    3. Connect the free end of the C-5343 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
    4. Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.
    5. Secure the FasCard reader to base as described in the F1: FasCard Reader Mounting Guide.
    Expand
    titleF2, F3, Flex, FlexRF

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.
    2. Connect the free end of the C-5344 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
    3. Connect the free end of the C-6348 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
    4. Connect the free end of the C-5500 Power Harness to port 1.
    5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

    Machine Configuration

    ...

    step
    componentMounting

    Cci readerinstall step
    componentPower

    Cci readerinstall step
    componentCoin Sense

    Cci readerinstall step
    componentStart

    Cci readerinstall step
    componentExtras

    Cci readerinstall step
    componentReader

    Cci readerinstall footer